SF385PEEW0 Whirlpool Range - Instructions

My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.

Screwed in light bulb and glass protector

1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes

removed the old ones.then installed the new ones.

I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.

Ordered the replacement part., removed the old trim from the door and reinstalled the new trim. On the drawer glide, I simply reattached a new one to replace the one missing.

The first challenge is always how to get the appliance apart; in this case how to open the top of the stove. There are two clips one on each side towards the front that you need to push in to release the top. However before you do this you need to unscrew and remove each of the burners from the top of the stove. After that, push the clips in with a flat blade screwdriver from each side to lift up the top. You will need to remove completely the top back plate on the rear of the appliance to get to the igniter module where you plug in the wires from the individual igniters. Then you also need to remove the top four screws from the lower rear plate to allow it to be pulled open enough to help thread the wire from the new igniter through. After that you simply figure out which wire (they are individually colored based on their position on the burner) and disconnect from the igniter module. Carefully pull it out watching where it came from so you can rout the new wire in a similar manner. Then remove it completely pulling it through the top of the stove and replace with the new igniter. Reverse the steps to put everything back together and you should be good to go. Be prepared to take a little extra time to clean the cook top as once you remove the burner you will see everything that has over the years accumulated between the burner and the stove top. All together it took me about a 1/2 hour (including the cleaning).

This is a built-in oven, so the biggest problem was figuring out how to remove it from the cabinet. The solution turned out to be removing the cooktop above it and unscrewing two screws that connected the oven to the inside of the cabinet. The other problem was removing BOTH metal backs from the oven. The first one was easy. The second one wasn't. The old socket was recessed behind the second back, making it virtually impossible to access the metal "wings" that hold it in place, so I ended up pulling out the socket assembly from inside the oven with pliers.

The replacement proceeds similarly as for electric range switch replacements described here, only this model is a gas range. The top panel does not lift up because of the feeds to the gas burners. It is possible, using a thin blade, to depress the spring fingers holding the switch in the oven panel, or else to remove it destructively. Be careful not to pull the old switch out too far, or else the wires will pull off the switch connectors and fall inside the oven-side panel cavity. This happened to me. The wires are very short. Another 1/2 inch of wire would have made all the difference. If this happens you have to fish out the loose wire. I gave up on this and took off the back panel (about 8 screws) and then loosened the bottom and sides of the side panel. This allowed me to retrieve the short wire and connect it to the back of the switch while pushing the switch into its mounting hole. Reattach the side panel, the back panel, and slide the stove back into place, and you should be good to go.

Removed the floor of the oven. Removed the flame difuser covering the burner. Igniter was in plain sight. Turned on the oven and saw that the element in the igniter did not glow. Removed the igniter. Found a replacement on this site. Ordered the replacement part, which I received 3 or 4 days later. Installed the new igniter. Turned on the oven. Saw the igniter element turn bright red. Replaced the difuser and the oven floor. Turned on the oven and bake 2 loaves of sour dough bread.

remove burner - 2 phillips head screws. Raise top - cut wire to ignitor. Strip wires and connect with a wire nut. Drop in new ignitor - reinstall burner.

Very easy. A couple of screws and it was repaired. Parts select makes it easy and affordable to do minor repairs on my appliance. This is the second time we have used this company to repair our oven and so far all has gone very well.

Removed the bottom drawer, oven racks, and the oven floor panel. With a #2 cross tip screw driver, I removed the old igniter, replaced it with the new one and tested the unit. When the new igniter began to glow I turned the unit off and reassembled the oven - JOB DONE less than 15 minutes.

just replaced the broken glides with the new ones.

I used a screwdriver to take two screws out and then pulled up on the burner head. I then installed the new part. It works great.