SF360BEEW0 Whirlpool Range - Instructions

Found that the two screws securing the bottom had rusted away allowing me to just lift the old bottom out. The new one fit in place exactly and really did not need the screws. Done in 2 minutes.

After removing the back of the stove, the old light socket was fairly easy to remove. The new socket slipped in place and the wires reattached and now the oven has a light again. A very simple process--especially for someone who's not an expert in repairing appliances.

it took 2 people to do this job. we had to place a yard stick inside the door to keep it open because after we removed the 2 screws inside the door that held the handle on, the door would not stay open. after removing the handle we had to slide the glass down from the top and line it in the slots at the bottom and then we had to replace the handle back on top of the stove, lining up the slots and the side pieces. after that we screwed in the 2 screws and yea! we did it right. The glass is in and we managed to not break it!

Removed back upper cover, unscrewed retaining screw from module. As noted in a comment from another do-it-yourselfer, I replaced screw with a longer one and reinstalled module. Note that the replacement part is not exactly the same as the old one(the wires are located differently), I noted the wire color codes with the slot number and reinstalled them in the same slot number. Works fine.

Remove 2 screws holding oven bottom in place.Lift out the plate and replace with new plate. The hardest part of the replacement was lining up the screw holes. By the way i have never received such great service from any internet company as Part Select. I ordered the part on a Monday and the part was at my home the NEXT DAY and installed that evening.

First I Pulled the oven away from the wall and turned off the gas and unplugged the oven. I then removed the bottom drawer and the oven door to get easy access to the ignitor location. I then removed the oven racks and the 2 shields which cover the ignitor with a screw driver. I then removed & unplugged the ignitor and 2 screws holding the ignitor in place. This all took about 15 minutes. I then reversed the process and installed and assembled the oven. It only took about 25 min in total time and low and behold the oven worked again. Amazing the technology stuff. My wife things I am a genius...again. Not!!!

Un-screwed 4 screws. Got part numbers off of the pieces. Put numbers in blank on web site and ordered the pieces. Parts cam in 4 days later and installed the pieces with my trusty screwdriver.

We replaced the part. It was pretty quick and easy to install.

It was easy to find the part. I ordered it on Sunday and it arrived Wednesday. A stress-free experience.

I tried taking the sensor out, but the plastic coupling behind the oven wall had melted and the melted piece was larger than the opening in the oven wall. I had to use a mini-screwdriver to chip away at the melted coupling before it would fit through the opening. That took forever...but it finally worked and the repair went quickly (15 minutes) after that.

Unsrewed what was left of the trim and oven handle. Just 4 screws total, then replaced the 2 screws of the trim and the 2 screws on handle.
Finished! Replacement parts fit perfect!!! Thanks a milliion!

Removed two screws holding the bottom in, pulled out old bottom, inserted new bottom, replaced screws and tightened them. Total time less than five minutes.

I didn't. Don't know how to get to light bulb to change it for this specific model

removed door handle screws then removed glass retaining tabs from sides put clips on sides of glass held insuation in place and replaced glass replaced door handle replaced two door screws trial opened and closed door successful done

First I removed the two screws that hold the glass cook top in place. Then I removed 4 screws that hold a small metal plate that shields the switch. Replacing the switch was very simply just a matter of unplugging four wire connectors from the old switch, sliding the new one in and reconnecting the wires. It was very easy to find the part on the website. I just located the switch on the diagram and ordered the part. I really surprised my husband that I ordered the part and repaired the stove by myself. He was intending on calling a repairman, but I did it myself.