IES426AS1 Whirlpool Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Frank from COLUMBIA, TN
- Parts Used:
- WPW10308477
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Heating element, broken
Unplugged appliance, removed the 2 screws that mount element. Unhooked the electric wires,with pliers.
Connected, the wires to new element replaced the 2 screws. And was done in about 9 minutes.
Connected, the wires to new element replaced the 2 screws. And was done in about 9 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melissa from MILL CITY, OR
- Parts Used:
- WPW10308477
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Extremely easy repair
Unplug stove. Remove the two screws attaching the element to the rear of the oven. Carefully pull out. Disconnect wires. Reconnect wires. Screw back in. Done. The hardest part was moving the stove away from the wall.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rebecca from LANCASTER, SC
- Parts Used:
- WPW10308477
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Baking element had burned into
The video was very helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wilton from CANYON LAKE, TX
- Parts Used:
- WPW10308477
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Oven bake would not heat up at all.
Very simple.
Remove 2 mount screws using a #2 phillips screwdriver.
Pull the element out to expose the 2 wires.
Using pliers, slip both wire terminals off the existing element.
Push wires onto the new element and install both mounting screws..
Done!
NOTE: The existing element showed no exterior signs of being bad.
The damage must have been internal.
Remove 2 mount screws using a #2 phillips screwdriver.
Pull the element out to expose the 2 wires.
Using pliers, slip both wire terminals off the existing element.
Push wires onto the new element and install both mounting screws..
Done!
NOTE: The existing element showed no exterior signs of being bad.
The damage must have been internal.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Yafa (and David) from Bothell, WA
- Parts Used:
- 8009
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Replacing the bulb in the freezer side
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- myron from west salem, WI
- Parts Used:
- WPW10299224
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Door hinge fell apart
Watched a video first. The repair was easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joanne from LAUDERHILL, FL
- Parts Used:
- WPW10299224
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Very hard to close the door range, especially one way and it sticks to close.
First, view videos to know what is an active door range problem.
Second, when you know the problem, see videos on you tube and be sure you will replace the right part
Third, I go to Part Select, see reference video for your problem if you need and buy the part on line, good price, very quick delivery.
Second, when you know the problem, see videos on you tube and be sure you will replace the right part
Third, I go to Part Select, see reference video for your problem if you need and buy the part on line, good price, very quick delivery.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Angelo from NAPLES, FL
- Parts Used:
- WPW10299224
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Active spring broken
Removed the oven door listened to a video/You tube and the rest was easy.When you remove the door panels make sure all the parts are assembled correctly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from HARMONY, MN
- Parts Used:
- WPW10181986
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
temp level uneven
after watching the video, installed the temp sensor. Super easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ralph from MARION, OH
- Parts Used:
- WP3149400
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Burner didn’t work right
Replaced switch. Works right now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glenda from ROCK HILL, SC
- Parts Used:
- WPW10299224
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Replace Door Hinges
So glad I found the parts I needed! I followed the GREAT video instructions on this site and when I opened the oven door up discovered there had only been ONE spring inside this whole time! I replaced both springs & hinges easily, cleaned up the glass while I had the door off, and everything went right back into place!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rosalind from APOLLO, PA
- Parts Used:
- WPW10181986
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
the oven temperature was not working right. I installed a new oven sensor. Works get now
Watch the video...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from THE VILLAGES, FL
- Parts Used:
- WP3149400
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Burner wouldn't regulate temperature
Turned off power to range. Took back panel off to reveal all controls. Pulled off knob of bad control. Removed 2 screws from the front of the control. Pulled off wiring from back of old control. Took new control reversed procedure. Reinstalled back panel turned power on and tested new control. Total time about 20 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Johnie from PARKERSBURG, WV
- Parts Used:
- WPW10308477
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven would not heat up.
Unplugged the range. Opened the oven door and took out the shelves. Took the right screw out, but had trouble getting the left one out do to the age of the range. Unhooked the two wires and took the element out. Put the new one in and hooked up the two wires. Attached the two screws and checked to see that the element laid flat and then tighten screws. Closed the door and plugged the range back in and turned the oven on and it worked perfect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RICHARD from DELTONA, FL
- Parts Used:
- WP3149400
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
8" FRONT BURNER STAYED ON HIGH HEAT/WOULD NOT REDUCE TEMPERTURE
REMOVE BACK OF RANGE, REMOVE BURNER KNOB. REMOVE SWITCH CONTROL REMOVE WIRES. REPLACE WIRES ON NEW SWITCH. INSERTED ALL WIRES REPLACE NEW SWITCH RE REPLACE ALL SCREWS. CHECK SWITCH. TURN BRAKER BACK ON. CHECK SWITCH FUNCTION. ALL IS FINE. PUT BACK ON RANGE SCREW IT IN PLACE. MOVE RANGE BACK IN IT POSITION.
Was this instruction helpful to you?
Thank you for voting!