Models > YWFE510S0HB0 > Instructions

YWFE510S0HB0 Whirlpool Range - Instructions

Jump to:

All Instructions for the YWFE510S0HB0

Customer:: Francis E from Harwich, MA
Parts Used:: WP3149400
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Element burned out

Element burned out, ordered from Sears. Took over 2 weeks to get, originally sent wrong burner then shipped second one to wrong address. When I installed element I found that switch was also burned out . I ordered it from Parts Select & it was in the stove in 24 hours from the time I ordered it on line. Be assured I know where I will order my parts from now on

Was this instruction helpful to you?

Customer:: Cliffford from Rochester, MN
Parts Used:: WP3149400
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Pliers, Screw drivers

Burner light was on all the time but burner was off.

Replaced the burner switch.

Was this instruction helpful to you?

Customer:: Howard from Land O' Lakes, FL
Parts Used:: W11171119
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

An Insect got in between the element coil & shorted it out

unplugged the range, removed the cooktop left & right front screws, unplugged left & right plug & unscrewed ground wire. Parts arrived fast & reassembled. . Happy, Happy, Happy! Happy Wife...Happy Life!

Was this instruction helpful to you?

Customer:: ROBERT from SALCHA, AK
Parts Used:: WP3149400
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Nutdriver, Screw drivers

Burner control failure/unable to regulate temp.

Unplug range from 220VAC outlet. Remove screws on back of range control panel and lift cover exposing controllers and wiring. Remove burner controller mount screws. Measure old controller shaft length/new controller shaft length (per instructions). Adjust new burner controller shaft length. Remove wiring from old controller (one at a time) and place on new controller. Install new controller and secure with 2ea mount screws. Re-assemble cover/control panel. Plug range into 220VAC outlet. Have wife ops check....everyone's happy.

Was this instruction helpful to you?

Customer:: Richard from Wooster, OH
Parts Used:: WPW10181986
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Stove kept turning off

Looked up on-line the error problem and what part I needed to fix it. Part arrived very quickly and everything was going fine until I realized the stove had two sensors. Replaced the top sensor now I am getting an error on the bottom sensor. Maybe I replaced the wrong one. I will replace the bottom sensor with the one I took out and see if that does the trick. Very very satisfied with PartsSelect. Good Price, Quick Shipping, Would do business with them again. They are now in my favorites so I can find them again if I need parts.

Was this instruction helpful to you?

Customer:: Dave from Titusville, FL
Parts Used:: WPW10181986
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

E-2 F-3 codes..Oven inop w/trying to bake.Beeps @ start attempt.

Contrary to instructions(go thru front of oven) I had to pull out the range, remove two (2) screws from back chassis. At this point you pull out the connector, snap in new, reverse proceedure. Very simple. Hardest part is cleaning up debris generated by moving range.

Was this instruction helpful to you?

Customer:: Ernie from Cameron, MO
Parts Used:: WP3149400
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Pliers

could not control temp on burner

Took appro 8 screws out of back panel, 2 screws holding switch, and pulled out switch, unhooked wires and reinstalled wires on new switch. Had to snap off stem with needle nose pliers which is simple and put everything back in place in reverse order!

Was this instruction helpful to you?

Customer:: Gene from Turtle Lake, ND
Parts Used:: W11171119
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

Burned out stove top burner

Easy change! Two screws in front and grounding strap screw-lifted out and turned stove top upside down on table. three more screws for burner element and then reinstall with first two screws and grounding strap screw.

Was this instruction helpful to you?

Customer:: Lynn C from Leesburg, FL
Parts Used:: WP3149400
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

Front large burner stayed on high

i personally did not do the repair..one of my neighbors did it and he said it was super easy..he pulled stove out from wall, unplugged it from socket, removed defective part, shortened clip that knob attaches to, installed new part with no problems whatsoever...plugged stove back in, pushed it back in place...burner now works fine! i was super impressed with the delivery of this part...ordered it on a Monday nite, it was mailed out the next day (Tuesday), and i received it Wednesday around noontime.. :)

Was this instruction helpful to you?

Customer:: Alfred from Ann Arbor, MI
Parts Used:: WP3149404
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Pliers, Screw drivers

Left front 8 inch burner knob control stop regulating heat temprature.

I purchased a new infinite control switch 6". and replace the old one.

Was this instruction helpful to you?

Customer:: Robert from Tonawanda, NY
Parts Used:: WP3149400
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Pliers, Screw drivers

Burner would go on and then turn off, repeatedly.

Unplugged unit, removed plate behind control panel, removed 5 or 6 wire connectors, pulled off burner switch knob and removed 2 screws that holds switch in place. Reversed the procedure and was done.

Was this instruction helpful to you?

All Instructions for the YWFE510S0HB0