RDE3600Y Whirlpool Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Terry from Grand Forks, ND
- Parts Used:
- 330031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
burner connector - bad connection
Removed burner and tray. Removed burner connector from stove top using screw driver.
Removed existing heat shrink and wirenuts.
Installed new connector - wire nuts and heat shrink. Used lighter to shrink.
Took 20 minutes.
Removed existing heat shrink and wirenuts.
Installed new connector - wire nuts and heat shrink. Used lighter to shrink.
Took 20 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Irina from Green Cove Springs, FL
- Parts Used:
- W10196406RW
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Ugly looking drip bowl.
Repair? What repair? I just removed the old drip bowl and replaced it with the new one. Piece of cake.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Tucson, AZ
- Parts Used:
- WP660533
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner replacement
Pug it in! That's it!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- dicky from mcrae, AR
- Parts Used:
- 330031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
replace burner coil connector
Cut the two wires approx 1 inch behind old connector and removed one screws to remove old connector, stripped approx 3/4 inch off the wires and connected them to the new wires on the new connector with wire caps and shrink wraps which came with the new connector. Replaced the old screw with the new screw and the job was completed. Be sure and disconnect power before starting!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg from Versailles, IN
- Parts Used:
- 330031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
large burners not working
Read instuctions first Turn breaker off to stove or unplug to be sure. Remove burner and drip pans. Remove scews holding socket in place if you are doing more than one make sure you keep in same location. Raise cook top untill supports latch in. Assemble plug it comes with two types holder compare to your plug. cut wire to old plug so you have enough wire to connect back with new. Strip wire back and place shrink tubeover wires wire nut together heat with a lighter or heat gun then do remaining plugges. place back in cover and replace scews. make sure wire are not to long to get under burner when cook top lowered. Lower cook top and clean burner plug ends with a little sandpaper to make sure they make good connection. replace pans and burner. turn on breaker or plug in stove making sure the burners come on when turned on good luck g.d.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Brookfield, CT
- Parts Used:
- WP660533
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner failure
Removed and replaced burner unit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- judy from coarsegold, CA
- Parts Used:
- WP660533
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burner fell apart
Just plugged it in and away I went.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gail M from Lockport, NY
- Parts Used:
- 330031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burner was slow heating at times. Moved back burner to front still same thing.
Unscrewed screw holding bracket. Used side cutters to cut wires. Replaced the bracket, put the shrink wrap on wires, twisted wires together and held with wire caps. Shrunk the wrap with lighter. I'm a 67 year old female.. No problems.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Germantown, MD
- Parts Used:
- WPW10196405
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
old drip bowl was worn out
new drip bowl fit perfectly and was a snap to install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary Kay from North Charleston, SC
- Parts Used:
- W10196406RW, WPW10196405
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner coil was falling apart.
Used new plug in coil burner.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Geraldine from Falls Village, CT
- Parts Used:
- WP660533
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The burner stopped heating
Unplugged the old one and plugged in the new, which you sent promptly. No tools. Easiest fix ever.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Craig from Bangor, PA
- Parts Used:
- WP660533
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner would not heat
Took the old burner out and inserted the new one. The burner was received two days after ordering. I was very satisfied with the service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elsie from Garner, NC
- Parts Used:
- WPW10196405
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
needed a new drip bowl and couldn't find ons that fit exactly but you had it
I removed the old one and put in the new one. Works great!!!!!!!!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robin from Chicago, IL
- Parts Used:
- WP660533
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner stopped heating up.
Searched the internet for the replacement part, placed the order and then disconnected the old one and inserted the new burner prongs into the socket. Worked perfectly!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Teresa from Kasson, MN
- Parts Used:
- 330031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Surface burner block corroded
It was a very easy fix. I followed the instructions that came with the kit and cut the original cable. Everything you need is in the kit; very few parts. Piece of cake and saved a lot of money an appliance repair person would have charged. This burner works better than the rest. I'm seriously considering replacing the other three blocks.
Was this instruction helpful to you?
Thank you for voting!