RS6700XKW2 Whirlpool Range - Instructions

I unplugged the stove from the outlet, then removed the two burners I was going to be working on and the drip pans. Then I raised the top part of the stove and removed the screws holding the plug-in blocks to the stove. Then I cut the two wires going to the old plug-in block and stripped the wires back to match the new wire parts. Then I placed the sleeves over the new wires, then I placed the new wire beside the wire I stripped on the stove and screw on the wire cap making sure it was tight. I repeated this three more times, once I had all four wires connected I then placed the sleeves over the connections and heated them up until they were formed around the connection. Once I had all the connections done I placed one wire at a time into the plug-in block until it locked into place ( I looked at my old plug-in blocks first to make sure I placed the new wires in the correct way ).I then used the metal mounting bracket that matched my old ones and snapped the correct one onto each plug-in block. Before mounting them onto the stove I compared them to my old ones to make sure they were correct. Then I used the new screws to mount them to the stove. I took a second look at everything I had done before closing the top cover of my stove. After lowering the cover back into place I put both the drip covers in place and then installed the burners.I then plugged the stove back into the outlet and tried the burners. This was very simple and the video on the web site shows this very well which made my job very simple.

Pulled off the one remaining knob, installed the new ones. One minute and the stove works perfectly.

I received my ordered in less than a week. It was great. The day I got them I remove the old burners and replaced them with the new ones. It took me about 3 minutes total. I was then able to cook my Christmas dinner with out any problems.

In my perpetual state of optimism, I hoped that the part description was incorrect and that the cost for the knob was actually a cost for a set of knobs. Woe to the consumer who doubts his own eyes! Yes, you will be paying about $25 after s/h for a single knob- but it matches, it works, it fits, and it takes less than 2 seconds to install, so kudos to the manufacturer who knew this would be a good form of supplemental income from their product... I still adore Whirlpool despite their exorbitant pricing on plastic knobs... :)

After shutting off the power, I removed the door and oven racks. Then, by using a screwdriver, I removed each element one at a time and replaced with the new element. Each element pulled away from the back wall and was connected electrically by Sta-Kon connectors. All went well, and the unit was operational in about 30 minutes. I still have to remove the oven from the wall to replaced the two door springs.

Purchased 2 piece broiler pan from this site

Turn Off Breaker.

Removed oven racks....

Removed two screws holding element in place...

Disconnect spade lug connectors from old heating element.

Connected spade lug connectors to new heating element.

Reinstall 2 screws holding element.....

Replace oven racks.

Turn Breakers back On.

Done 10 Min. Install

Removed the two Philips head screws that attach the element to the back wall of the oven. Pulled off the two wire terminals from the spades on the back of the element. Pushed the two wire terminals onto the spades on the back of the new element. Noticed that one was not tight, so disconnected, squeezed down the wire terminal, and reconnected. Inserted the two screws that attach the element to the back wall of the oven. Element works fine.

This is an easy fix. Just before the holidays, it was imperative that this appliance be in top shape. Since the door 'hung' wrong, it was determined that the hinge pin broke. Remove the 2 phillips head screws on the door and open the door to the to a 15 degree opening. This position allows you to slip the door off the hinge levers. Now that the door is off, replace the hinge pin and slip the retainer ring on with a screw driver blade to push it on the pin. Slide the door back on the levers and fasten the retainer screws. DONE!

My husband wanted me to call a repair man but I had read online how easy it was. I received my element in one day from Fresno, CA and followed the instructions given by others on line. I couldn't believe how easy it was. The most difficult was removing the connectors because they were stuck. I used needle nose pliers as someone suggested. Saved the cost of a repair man.

lifted hood top unscrewed 4 small screws opening lid to switch housing took out 2 small screws that held the switch and then transfered wires to new switch replaced new switch with 2 new screws and back to working again walla! Time spent less than 30 minutes very simple as the instructions were very self explainatory.

two Phillips head screws hold the oven unit in. It culls out and the wires just disconnect. Reinstall in reverse and test.. The burner socket I cut the wires from the old socket and splice the new pigtails onto the existing wires and install the socket. The instructions in the package are good for people that aren't used to doing repairs.

The honeycomb filter in the vent was missing so I bought the entire vent cap.. Thought it attach with 2 screws from inside the oven.. BUT -- when you loosen the screws, it wouldn't drop.. Looked at the new part and saw that it attaches to the vent outside the oven as well.. So to replace this puppy, you have to pull the cabinet apart..

Left it for another day.. Hopefully no grease fires..

First I removed the ovem door, then I removed the 4 screws, unplugged element and plugged in the new one, then replace the screws and door. It should have been a 10 min job but I'm old and a bit fat...slowed me down.

1. Move oven out from wall 2. Remove back panel of oven, 8 screws 3. Remove 3 screws inside oven holding element 4. Pulled wire connections off of element 5. Reverse procedure to install new element