Models > GS440LEMB1 > Instructions

GS440LEMB1 Whirlpool Range - Instructions

Jump to:

All Instructions for the GS440LEMB1
121 - 135 of 159
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
David from Johnsburg, IL
Parts Used:
8190618
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Oven would not ignite.
Removed the old burner and instlled the new one. It works great and I am a hero!
Was this instruction helpful to you?
Thank you for voting!
Customer:
Paul from Adamsville, TN
Parts Used:
WP8523166
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Side trim broke
take the 2 screws that hold the handle on out...watch the glass front and the side trims because the handle holds them on. Take the glass out then remove the side trims. Replace the side trims holding the glass in place with 2 pieces of masking tape om each side then install the handle with the 2 screws and remove the masking tape.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Lee from Saint James, NY
Parts Used:
WPW10107820
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
Gas range would not go into self cleaning mode. When pushing the self clean button, would get three beeps!
The malfunction was narrowed down to the oven door motor lock, located at the upper left back of the unit. Removed two panels from the back of the unit, 8 screws. Then the motor, 2 screws, 4 wire connectors. Reversed the procedure for the installation, and solved the problem. About 30=35 minutes for the job. If your handy at all, it should not be a problem.
Was this instruction helpful to you?
Thank you for voting!
Customer:
melody from springhill, FL
Parts Used:
WPW10118456
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Broke front glass of oven while moving
Looks better than the old one wes and so easy to do. Thanks.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Paul from Cornelius, NC
Parts Used:
WPW10181986
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
oven temperature did not stay as set
changing the part itself was easy, but the sheet metal covering the whole back of the oven was difficult to remove because of some screws that were stripped. The new sensor solved the problem.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Thaddeus from Washington, DC
Parts Used:
WPW10118454
Difficulty Level:
Difficult
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
broken outer range door glass
Using 4 strips of duct tape was useful,in holding the glass to the door.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Thomas from Decatur, IL
Parts Used:
8190618
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
The oven would not light
First remove the oven racks and the burner cover in the bottom of the oven. There are two phillips screws near the back. Loosen the screws but it is not necessary to completely remove them. Pull out the bottom cover and this will expose the burner. There is one phillips screw at the front of the oven and one at the back. Remove these screws and set aside. You should be able to remove the burner and unplug the wire connected to it. Replace with a new burner in the reverse order. Plug in the wire and make sure the new burner is seated properly over the gas valve. It lines up pretty easily. Put the rear screw back in but be careful not to drop it into the hole otherwise you will have to use a magnet to retrieve it or pull the oven out because it will be on the floor. Replace the front screw and put everything else back together. Pretty easy job
Was this instruction helpful to you?
Thank you for voting!
Customer:
Karen from Maryland Heights, MO
Parts Used:
WP3195546
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
The front drawer glide broke
Very easy. A couple of screws and it was repaired. Parts select makes it easy and affordable to do minor repairs on my appliance. This is the second time we have used this company to repair our oven and so far all has gone very well.
Was this instruction helpful to you?
Thank you for voting!
Customer:
larry from fairfax, VA
Parts Used:
8190618
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers, Socket set
oven would not ignite
Remove oven racks. Remove bottom of oven. Mine was held in place by two large screws in the back part of the oven. They did not screw into anything. Lift out bottom from the rear. Remove burner cover plate by lifting the front and pulling out. Mine was not screwed in. The igniter is mounted on the burner and held by two 5/16 small bolts. The top one is easily accessible. The bottom is a real witch. You need 1/4inch socket set with universal connector to remove. There is a single wire attached to igniter by a wire clip. The wire is accessible by removing the bottom pan storage drawer under the oven door. Unclip the old attach the new. Screw two small bolts back in and replace things you took out. TURN GAS AND ELECTRICITY OFF BEFORE YOU BEGIN. Parts select should allow the igniter to be sold separately rather than connected to the burner. I only replaced the igniter. Replacing the burner would be a real chore.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Richard from Wooster, OH
Parts Used:
WPW10181986
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Stove kept turning off
Looked up on-line the error problem and what part I needed to fix it. Part arrived very quickly and everything was going fine until I realized the stove had two sensors. Replaced the top sensor now I am getting an error on the bottom sensor. Maybe I replaced the wrong one. I will replace the bottom sensor with the one I took out and see if that does the trick. Very very satisfied with PartsSelect. Good Price, Quick Shipping, Would do business with them again. They are now in my favorites so I can find them again if I need parts.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Ken from Las Cruces, NM
Parts Used:
WPW10181986
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Oven shutting off after temp reached 350
Remove the plug from outlet then shutoff gas. Remove the 10 screws hold the back panel of the oven. Unclip the connector of the temperature sensor from the main line. Pull the sensor straightout. Reverse the process install the new sensor. Couldn't be any easier. Oven working great. Calling in a reapairman would have cost $200 for parts and labor.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Mike from Chicago, IL
Parts Used:
3196152, WP3195097
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
The old panel becamed worped & the finish was distressed.
Took the old one out and replaced it with the new one, fits perfect.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Dave from Tampa, FL
Parts Used:
WP3195546
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
The old glide broke
Its was very easy, I unscrewed the old part and screwed on the new one and put the drawer back in place and it works perfect.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Raymond from Ashland, WI
Parts Used:
WPW10202217
Difficulty Level:
A Bit Difficult
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Scews from old one didn't fit the new one.
I had to bring the new handle to the Hardware store and have them pick out screws that would work. The only problem is that I live 12 miles one way from the Hardware store. My advise is to order scews when ordering the handle.
Was this instruction helpful to you?
Thank you for voting!
Customer:
CONSTANCE from LAWTON, OK
Parts Used:
WPW10202217
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Broken oven handle
I removed the handle from the door, replaced the old one with the new one............. 1, 2, 3, just that easy. The replacement part arrived very quickly and the price could not be beat. Would I use them again...........Yes!
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the GS440LEMB1
121 - 135 of 159