WLP83200 Whirlpool Range - Instructions

The repair was very easy. It took me less than ten minutes. There were only five screws including two to hold heat element that I have to unscrew and transferred the old clip the screw onto new heat element.

Replaced both rollers....Quick and Easy!!

2 screws,coule plugs,test_OK.Fully functional for days now. Thank you !

This job replacing the was so easy, it took about ten min,to do it thanks

I went to the source of power on the stove and noticed one of the terminals had come loose from the terminal block and had shorted out against the cover of the terminal junction. After prying the loose terminal off cover I ordered new terminal block and received it the 2nd day. I removed the old terminal block and replaced the part in about 10 minutes..Thank you Parts Select for your easy to find diagrams and quick delivery.

looked it up on line how to change it. before I ordered part, to see how much of a job it was. was real simple to change, had no problem. also part select sent the correct part. Job went well

Removed the door. Took out all the screws. Removed the glass that was cracked. Put in the new piece. Put the screws back in place. Put the door back on and it was a done deal.

Remove power from appliance, verify power is off. loosen two side screws that hold cook top to counter top. Gently push appliance up from bottom, everything from now on is done gently !. every component is very fragile. hope you have enough room to move cook top to side, if not, have help to hold it for you. #2 screwdriver, remove screws on all sides, two front, 3 sides, 3 in back. Note placement of connected wires in the affected element. # 2 screwdriver remove one screw on bar holding set of elements, lift and loosen metal spring and remove element, ply wires off with pliers. ( I suggest you clean inside cook top if needed) Note place of springs(Numbers) and remove to place on new element. reverse order to complete.

Open oven door and remove two screews with 5/16 nutdriver to remove hole top of stove.Just lift up gently on front of top and pull toward you and when about 4 inch clearance on back of top you will see where all the wires connect ,press the side tabs of this big connector and it will release very easy to remove the top.Place top on bath towell upside down on countertop and remove 4 screws and 2 clips on the bad burner with the same 5/16 nut driver and remove the three wires and reinstall the same way then reinstall the top on the stove in the same order.Very Easy Job

Step 1. Always ensure appliance is unpluged from power source. 2 Remove oven door by open slighly and lift up be sure your hands are up from hinges they can snap back and injure fingers. 3. Have a cover on a flat surface and have a diagram of oven door, 4. Remove bottom screws and slide out top glass and side rails. 5 Remove top cover and insulation over glass. Beware of any jagged glass. 6. Incert new glass. 7. Be sure when replacing insulation and cover that cover in under tabs to ensure glass is firmly held in place repeat steps in reverse order. Took just 20 minutes to repair. I used a small electric screw driver.

I got the new wheel and screwed it in by hand. It took like 4 minutes total between taking out the drawer, screwing the new wheel on, and putting the drawer back in

By following the instructions, I exchanged the surface element. It was very easy. This was my first time fixing it too.

Although I put 15-30 mins for repair, most of that was taking it apart only to have to put it back until I got the right part. It can be done in 15min or less. FIRST: UNPLUG THE RANGE or Shut the circuit breaker OFF. Remove two screws (1/4" nut driver) on the front lower edge of the cooktop. These are seen once you opent the top oven door. Lift up the top and pull out about two inches and disconnect the multiwire plug in connector. Lift the top off the range and place it upside down on a flat surface (talbe or counter) protected with a towel. Unplug the sliding connectors from the burner unit noticing the correct placement. Remvoe the two tabs (#2 phillips screwdriver) on either side of the burner unit noting location. Take the time to clean up all debris with a vacuum or soft cloth. Install the new burner, connect the two tabs, plug in the connectors, return the top to the range, plug in the multiwire plug, secure the two screws and plug the range back in and start cooking!

pulled door up and out. Disassembled door. removed old glass and rope gasket. installed new glass and gasket.

Removed back panel on stove and found no continuity in bake element indicating a break in the element circuit. Also tested electrical supply up to the element and found that we had electricity up to the element when the oven was turned on. Went on line and ordered the bake element and it was on my doorstep in 48 hours. Remove 2 screws inside oven and disconnect wires from the rear and install new element and plug the 2 wires into it, replace rear panel ( 3screws) and turn electricity back on to the stove and you are back in business.