GR440LXMP0 Whirlpool Range - Instructions

Removed two screws that held the unit in then pulled out a few inches so I could see where the 5 wires were. Then I replaced one at a time till done. then replaced the retaining screws.

First we unplugged the range. My husband removed the old element using a screw driver. He also removed the back panel on the oven after pulling it out from the wall. He unplugged the broiler prongs and plugged in the new element, put it all back together using the screw driver. We plugged it back in, turned on the oven and it is working great! Simple and easy to do in a short amount of time. Cool!!

Turned off electricity! Pulled stove out -lifted up glass top(carefully) simply removed burned out coil and replaced it with new one.

Since no instructions are provided with the part and not having seen the oven with the glass door in place, the major problem was figuring out how things went together. The top handle MUST be removed and the bottom trim need not be (although I had already done so). After removing the top handle the glass slips into the bottom trim easily, but the edges set ON TOP of the side plastic trims (left and right), not under the edge as it would appear if you have never seen the original door in place. Properly positioning the glass door then lets the top handle slip back on and the two screws replaced to hold it all to gether. Another pair of hands helps hold it all together until the top handle is fixed back in place. It's quite simple in reality, and instructions would have made it so.

Google the error code that the range was displaying and found others with the same symptoms. Then found several people that had fixed the problem by replacing the oven sensor. I then ordered the sensor and replaced it, which fixed the problem.

We removed the door from oven assembly and laying it flat on the bench removed the stainless steel cover from the rest of the door. Removing the shattered pieces of safety glass was done heating and scraping off vinyl tape.(difficult.)Caution! Do not allow any pieces of glass get under the stainless steel cover, it will leave ugly scratches! We purchased double sided vinyl tape 1/2" wide, 1/16" thick and aluminum "Flue tape" (600 deg. F) 1 1/2" wide from local hardware store to replace the original ones in their previous location. Fitting the new glass on sticky tape has to be done accurately. (no problem). Assembling it was little tricky but still within the ability of a do-it-selfers. We wondered if we should not put the rough side of the glass facing in or out. The original was with the smooth side out so that what we did. If any additional scraping of accumulated grease is needed especially on the inside glass, it requires more disassembly, but we would strongly suggest doing it (we did), while it is all opened. To our surprise the glass arrived by Fed Ex within 24 hours of ordering and now our Whirlpool is gleaming like new again. The cost of this product with shipping/handling by PartsSelect was much lower than ordering it from the other "original" source. Thank you! Sincerely Fred T.

Puled out the electical plug . Removed the back panel. Pulled off the switch knob. Removed the 2 screws holding the switch. Took the wires off of the old switch and placed them on the corespondig connector on the new switch. Put everything back in reverse order.

Tried to do it myself and broke the left trim piece. Use two people!

Removed oven from wall unit and took the back off. Removed the old socket assembly by depressing the ears and forcing unit into the oven. The electrical wires were easily removed since they are spade connections and slip off. They also are different sizes so that there is no chance of erroneously putting them back in an incorrect order. The new unit simply slips in from the front and snaps into place. The most difficult part of the entire process is removing the old unit. A little "friendly persuasion" is required to get the old unit out.

1. Disconnected power from my oven.
2. Removed several screws that held the control block
3. Removed two screws that held the switch itself disconnected wires and removed switch
4. Reconnected all wires to new switch (no soldiering gun required)
5. Put control block back

Overall - very easy

Safety first always shut breaker off at box.
I unplugged stove, disconnected wires keeping in mind the color placement. Unscrewed one ground screw and removed terminal block. Attached new block with ground screw, replaced wires in correct order, re-attached plug. Then reattached safety cover. Pretty simple for d.i.y.

1. tripped circuit breaker for stovetop
2. pulled the stove top out of its cabinet.
3. turned in over carefully due to the glass cooking surface.
4. used 1/4 inch nutdriver on cordless drill to remove all the screws holding the lower cover in place. lifted cover off without removing completely as power wires still attached.
5. did continuity test on burner and found it open circuit while all the other 3 burners had continuity.
6. removed defective burner by removing two more screws and saw element was fried on the cooking side.
7. wrote down all part numbers and put it all back together.
8. changed the burner out when new one arrived by repeating steps 1 thru 6. Pay attention to the correct wiring setup. Do one wire at a time to make sure you don't mess up. MAKE SURE THE CIRCUIT BREAKER IS TRIPPED BEFORE YOU KILL YOUR SELF.

Have a tall one to celebrate the savings of two repair man call out fee's of minimum $60 each time and paying list price for the element. You probably just saved yourself $150.
Tom in Steinhatchee

First discount Ac from wall, then take out 2 screws on the front of the range top and lift up the top of the range surface, then while holding up the surface top take out the front burner and replaced new burner element.Let the surface top down and screw in the two screws. the surface top of the range is hinged so it would be good to have someone to hold the top up while you replace the element or use a piece of wood to hold it up,this is a piece of cake to repair. would like to thank parts select for their service. I have ordered from them before and they back up their products
Robert

Turned off the power . Removed two screws in front, lifted top, used a piece of wood to hold up,took off wires to bad element removed old element, replaced with the new one, put wires back on ,closed top,screws to front,on with power and cooked dinner!

Very easy . Just removed four screws and removed the back cover. Then just unplugged two clips from the element . The repeated all of my steps in reverse . Be sure to unplug the oven before you start on the project .