RDE6550A-1 Whirlpool Range - Instructions

I found the received switch (PS12070192) a poor replacement for the original, or even the earlier replaced part (PS11744446, in 2016) I was going to replace since the press/return feature seemed slow to return.

The male spade lugs on the received switch are so positioned that engagement is only possible if the lug is bent out at a large angle. The lug set-back from the body edge, and the raised ribs on the sides still prevent full engagement of the connections.

I did install the new switch but found that was the only switch that didn’t give a signal light when turned on.

I have reinstalled the earlier unit.

Is part# PS 11744446 no longer available?



James E Weimholt. jmwm4031@verizon.net

Lifted range top, disconnected and labled wires from old switch, removed old switch, replaced wires on new switch, installed new switch.
NOTE: Local appliance store informed me that the electric cooktop was too old and that a replacement switch was not available and wanted to sell me a new cooktop for $795!
I found the switch on PartSelect and repaired the cooktop. Total cost... UNDER THIRTY DOLLARS!!

Well, when you put the back cover on and screw it down make sure you have nothing touching the white wire leading to the oven light. I did and it blew the push switch when I threw the 220 breaker. Actually, the light was on when I came in the room, but when I pushed the switch on the front panel it sparked in the rear and popped the breaker. Then I saw the short and when I tested the switch it would not click. The install was fine.

First cut electrical circuit to oven for safety, then removed screws, two Phillips head, removed two wires from element, and put some clips on those wires so they wouldn't fall behind the oven wall. Then I got the new element, put on the two wires removed from the old element, attached element to rear wall of oven with the two screws removed previously, closed circuit breaker to oven, tested oven and it worked fine! Just like new. Standard shipment was plenty fast enough.

Turned off circuit breaker. Removed two mounting screws and pulled element toward front of oven to reveal one wire on each side clipped to element. Removed clips from old, then reconnected to new element. Pushed back in place and reinstalled two screws. Turned circuit breaker back on and ops checked. Very straight forward repair.

Turned power completely off. Removed knob from front panel. Opened range top cover. Removed 3 screws from aluminum panel protector behind the element switch. Once panel is removed you can see the switch element. Remove 2 screws from the front panel that connects to the element switch. Remove the old element and replace with new element making sure that each of the 5 wires on the old element is transferred one by one to the new element. Reverse the process in putting it all together. Turn on the power and walla you've have a new stove. You just save $600 plus.

Inserted replacement knob in place of the broken knob

Dean was very helpful. He looked through the numerous model numbers and found just the correct knob even though the model number was no longer in use. I'll be calling back with another repair problem soon. Thank you very much.

Very easy. Removed shelves after turning off breaker then removed screws holding element and removed screw holding wire. Removed old element and then placed new one. Attached wires with screw and then placement screws. Turned on break, replaced shelving racks and turned on. It worked and 5-10 minute fix.

Removed the knob from package and placed it on the post which held the knob.

I unscrewed the element from the oven where the ends enter the back of the oven. I pulled out the element ends and unhooked the wire connectors being careful not to let them pull back into the oven wall. I connected the wire connectors to the new element, making sure that the front support was pointed down, and replaced the screws.

First shut off breaker to oven before starting the repairs. Removed old unit by removing two phillips head screws at each side above element entrance. Gently pull element out to expose wire attachments. Remove wires from each side careful not to lose wires inside back of oven. Replace with new element,(which was ordered online, and received within three days)in reverse order in which it was removed. Turn breaker to oven back on. Oven like new and ready to bake.

Removed the small metal panel covering the main power terminal in back of the electric range. Removed the nuts holding the red, white and black electrical wires from the range using the appropriate socket (there will be two nuts on each bolt end). Removed the two screws holding the main power terminal block with appropriate screw driver. Connect the new main power terminal block to the range using the two screws. Reconnect the red, black and white electrical wires coming from the range using one nut for each wire. IMPORTANT: do no over tighten the nuts because the bolts could snap. Reconnect the pigtail and secure the small metal panel covering the main power panel.

Ordering the part online was easy. It arrived in a timely manner. I found a terrific video online showing how to install the terminal. It was so easy. Thank you for the great instructional video.

Unplug power cord, remove wires from block. take 2 screws out. replace with new block about 15 mins. Done