SF360BEEZ0 Whirlpool Range - Instructions

I use the table knife to slide the side of the stove to open the top. then I traced one of the wire to where it was hooked up and remove it and replaced it. I did them one by one.

took 2 screws out of bottom plate in the oven and lifted it out. removed 2 screw on the flame deflector and took it out. Took 2 screws out of old ignitor and unplugged it. Installed new ignitor tested oven put it back together. took about 30 min. screw driver only

Unplug the stove. Remove the burners. Release the top of the stove by using a screwdriver to push in the spring clips on each side of the stove top. Pull out stove to access the back of the stove. Remove the back plates. Identify the defective igniter wire and remove. Install the new igniter wire. Screw the back panels back on. Snap the stove top back in place. Reinstall the burners. Push the stove back into place and plug in the stove. Test the burners.
One precaution - make sure you do not move the gas tubing under the stove top out of position. If you do, make sure you put it back in line with the gas valves.

We removed with a screwdriver the two main screws that held the bottom of the oven in place and removed the bottom oven piece; then we removed the two nuts with a socket wrench that held the element in place. We then discovered that the element wire did not completely egress to the point of being able to disconnect from within the oven, so we removed the storage drawer below the oven and that provided access to disconnect the element wire and reconnect the new element wire and then reverse the steps to install the new element, which worked fine upon first use and continues to work fine.

Had to remove the bottom oven shelf and the broiler drawer. Disconnected the wiring pigtail theought the broiler opening and pulled the gas pipe from the baking oven. Reomved the two screws connecting the ignitor from the pipe. Connected the new ignitor and threaded the wiring pigtail back down the the opening in the baking oven. Connected the wiring harness up inside the broiler and put the drawer back in. Re-installed the bottom shelf in the baking oven and tested. Worked perfectly. Back to cooking. :-)

Oven is gas. Burners on top OK, broiler in oven OK. Removed oven bottom plate and heat deflector. Carborundum igniter would not glow. Ordered new igniter from Partselect.com. With new igniter in hand I unplugged the oven from house power, removed the bottom drawer for access to the igniter connector, and disconnected it. Removed the bad igniter and replaced with new igniter...easy! Plugged in oven to house power and tested new igniter by turning on oven. GOOD!! Reassemmbled oven interior. Wife again happy.

took out old oven bottom by removing 2 screws, placed the new oven bottom in place put the screws back in and was done.

Called repair man and described the problem. He said I could do it myself. PartSelect had the part and a previous description on the PartSelect site told me how to do the repair. It was easy. Be careful when removing the igniter nuts. I used a very small amount of sewing machine oil so as not to strip the threads. works great.

just replaced the broken glides with the new ones.

Undid one screw. Removed the broken slide. Replaced with new slide an fastened with the existing screw. Problem solved.

Used a phillips head screwdriver to remove the single screw holding the part in place and put the new one on. Finding the part on this site was a breeze and it arrived quickly. A first rate experience all around.

Took the back off the stove, removed 2 screws, unclipped the bad sensor, clipped the new one on, put the screws back in and the back of the stove back on and that was it - 10 minutes

DISCONNECTED POWER AND GAS TO THE RANGE. REMOVED 6 SCREWS FROM REAR OF THE RANGE. REMOVED THE 2 SCREWS HOLDING THE TEMPERATURE SENSOR IN PLACE. DISCONNECTED THE LEAD FOR THE SENSOR. INSTALLED NEW SENSOR IN REVERSE ORDER. OVEN WORKING PROPERLY NOW.

I used a phillips screwdriver and replaced the part with one screw.Very easy and replaced my lower drawer under my oven,it tool about three to five minutes at the most and my drawer works fine now.Thanks for the instruction video on line, it really helped.

It was alittle difficult at 1st to remove the clips that held in the socket. But once out everything went smoothly.