RF327PXVW2 Whirlpool Range - Instructions

The hardest part was figuring which breaker controlled the oven because it wasn't marked in my breaker box (it IS now!). So, first I killed all power to the stove, then unscrewed the 2 screws in the back of the oven holding the element. Pulled the element forward, then dissconnected the 2 clampy connector wires (yes, I'm a girl, no correct electrical jargon here). These were a little difficult because my oven is 21 years old & this is the first replacement I've had to do. I reconnected the new element clamps(which was easier), pushed the wires back through the opening & reinserted the screws. Threw the breaker back on, turned on oven to 200 degrees & let heat until the set temperature light turned off as a test. Voila - oven fixed!

I'll tell you.......PartSelect said the items would take from 3-5 days.....I got them in 48 hrs. I turned the breaker to the oven off. I unscrewd two screws from the back of the oven and pulled the element out and took it off of two connectors. Repeated the same with the broiler element. Job done saved $200.00...Job was quoted at $259.00

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.

Shut off circuit breaker to stove. Removed oven racks from oven. Removed two phillips head screws located at the base of the bake element at the back of the oven. Gently pull the element toward the front of the oven until the wiring connected to the element by spade connections can be reached. I used a pair of pliers to help separate the element from the wiring. Removed disfunctional element from oven. Sweep out the bottom of the stove with a dustpan & brush. Lay the new replacement element on the bottom of the oven. Connect element to wiring via spade connectors. Gently feed the wires back thru the holes until the the tips of the element follow thru the wire holes until the base of the element is flat against the back of the oven. Screw in screws thru the base to the back of oven - tighten tight. Reset cir brkr. Test oven.

I removed the screws that hold the element in place .
Pulled the element out enough to disconnect the two wires . I then connected the new wires and pushed in the element . I finished off by screwing the bolts back in place.. Voila!!!!!!! I was in business once more!
The part arrived within 48 hours and was very reasonably priced

Replaced for a friend who was financially unable to purchase the unit. Turned off power to stove. Removed two screws. Inserted the unit and replaced the two screws. All fixed in about 15 min. Now she can enjoy baking again.

followed the instructions. removed the old element and installed new one.

First I removed the two screwes that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires from the old element, then I connected the two wires to the new oven heating element. Pushed the unit back in place and reinstalled the two screws that hold it in place.( ALL Done)

Fairly easy to do. Part arrived very quickly. Appreciate

associate's help in making sure part was right.

Don't know, left the room.

Shut power off to stove, by turning off breaker. Using a screw driver, removed the 2 screws securing broken bake element to back of oven wall. Grasp the 2 wires holding the prones & gentley removed broken element. Attached new bake element to wires, put screws back in & secured to oven wall, turned breaker to stove back on. Oven works great, had pizza for dinner.

Well it was quite simple to replace all I used was a long Phillips screw driver,the job only took me 10 minutes to complete,thank you so much for the part you sent me it was the correct part.

Unplug oven unit from outlet or flip the breaker to disconnect the electricity. Used screwdriver to remove face cover, pulled wire connections from posts of old bake element. Attached wire connections to posts of the new bake element(they just slip on the posts). Aligned the face cover flush with the oven wall and replaced screws to hold cover on. Reconnect electricity and ready to bake. It is very simple.... We were very pleased with how quickly the element was delivered after ordering it.

I just removed two screws and disconnected the push on clips I then cleaned the botton of the oven and replaced the element. And it works just like new.