WWEF3004KWD Westinghouse Range - Instructions

Removed the one remaining drawer guide and stared at it for 10 minutes trying to understand where it came from and how it worked. Looked it up on partselect.com. While there was no part number, the detailed photo on your web site was enought to assure me that you had the correct part. Ordered them in a few moments and three days later I had the parts. The hardest part of the job was trying to understand how to install the widgets. After 20 minutes to crawling around in the stove's inards, I finally got the "aha" and the drawer on this antique stove was finished. Thanks! Couldn't have done it without you.

I first turned the power supply off to my oven. Then I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the ends. After that I connected the new element to the wires on my oven and secured the element with the two screws and turned the power back on. I pushed the oven-on button and now I'm back in business.

I went all the way around the unit and removed screws holding top of unit in place. Removed knobs holding front panel in place. Remove control panel. top should come off. Remove screws attaching element top and metal frame. Undo bracket and remove element. Disconnect wires. Remember where they were attached.
Replace element and reverse steps.

Disconnected power. Removed hold down fasteners for stove top. Fortunately, I did not flue down or use the double back tape to secure stovetop to counter. If this adhesive were used, it is possible I would have had great difficulty in removing range. I did not disconnect the wiring, but turned the range top over to access the cover. I removed the cover and easily removed the failed burner and installed the new ones. I had to pull 4 wires from the terminal strip and reattach them. The hold down strap for the burner was reinstalled. Range top turned back over and fastened down. Back in service.

it was an easy repair, and i thought it was the clock /timer, but it was the probe.

Followed the instruction printed on the page, while ordering the part.

Slide out the old; slide in the new!

I tested incoming and outgoing voltage at the timer! The timer showed to be defected!

New part arrived, opened pkg. , Pulled drawer out. . . Snapped in new parts. . . . Done!! Saved myself $100. 00.

When I pulled the element out of the back panel of the oven to remove it, the electrical connection got caught on the edge of the hole in the panel and disappeared back into the oven insulation. It was difficult to find and pull it back out to reinstall it on the new element.

First I unpluggd the range and removed the back cover using a nut driver. Then I removed the knob by pulling (using a little force),Not very hard to do. I uscrewed two screws that hold the switch from the front of the range. Then I pulled the switch out about three inches and used pliers to disconnect the wires one at a time and connect them to the new switch. finally I finished the installation by reversing all the steps. Total time to install the switch took approximately 5(five) minutes.

Removed back off of stove. Removed two screws that held in the switch, removed the wires that were connected to the switch and replaced the part.

Twisted replacement bulb into place easily. Let there be light!

First i removed the two screws that hold the element
in place. I the pulled the element out about 3 inches and disconnect the 2 wires. The new one didn't come with the little holders at the front of the element and were very hard to get loose from the old element .i finally got them back on the new one and put it back in the stove. Pretty simple job though.

Slid oven out removed one screw one plug replaced part took 5 minutes.told parts repair the error message and they sent me the correct part in two days will use them again saved me from Repair man wanted 85 dollars just to look at it my cost was 28 for probe and 8 dollars for shipping already helped neighbor with their stove they needed new ignighter 12 dollars repair place want 110 to come look at it this site walks you through repair best service!!!!