WWEF3002KWB Westinghouse Range - Instructions

took out the old one, screwed in the new one. very easy.

This is an easy repair, as described in several other replies. One important addition to what has already been described. Very important to turn off the breaker or unplug the range. One terminal of the range is connected to a hot wire and the range housing is grounded. You may not manage to electrocute yourself, but you could cause and arc that damages the housing or connector. Turn off the power. Beyond that, simple. Unscrew two 1/4" screws with a nut driver, slide the element out and disconnect the wire connectors. Reverse procedure to install the new element and turn the power back on. Preheat briefly to burn off any odor. Very easy repair.

Just followed the instructions

Sat on floor, pulled drawer out, inserted new clips, remounted door, stood up, high-fives myself.

first thing was to turn the breakers off. then pull the range away from the wall. used an 1/8 th inch socket to take off the back panel to get access to the switch.used a Phillips screwdriver to disconnect the switch under the knob in the front. took off the wire terminals one at a time and matched it to the numbers on the old switch.replaced the knob, screwed it on to the range. turned the breakers on and tested the switch.worked fine, replaced the back cover and pushed it back into place.

I simply followed the instructions in your video. i shut down the power to the oven via the breaker panel, removed the two quarter inch screws with a nut driver, pulled out the old element exposing the two wire leads,disconnected one lead at a time and duct taped each lead to the oven wall,. Then removed the old element and replaced the new one in reverse order. Voila! It works great. This is the second element I replaced in this oven over the years. This site was prompt on shipping the new element (about 3 days since I ordered on a Sunday).. It was well packed and arrived on time and I even got an e-mail letting me know it arrived! How cool is that?! I've been a customer for a few years now and plan to be a "forever" customer. Thanks for saving the day! You ROCK!

Simply...2 hex head screws removed. Unplug old element...plug in new element...place 2 screws back into place...test

Remove 2 screws. Pull element out. Slide 2 wires off. Just do in reverse it's done.

The broil element and range were both working so I removed the bake element to test for continuity. Use a 1/4” socket or wrench to remove the two screws holding the bake element to the rear wall of the inside of the oven. Pull the ends of the element out of their recesses taking care not to lose a wire inside the back panel of the oven. Pull the wires off the element ends. You should be able to do this by hand; use a flathead screwdriver for a little prying if necessary. Visually inspect the element for physical damage. If you don’t see any, test the element with an ohmmeter or multimeter. If it reads anything other than 0 ohms (continuity), your element is defective. Installation process is reverse of removal.

Using a socket set and Robertson #3 (smallest) driver head,with the breaker shut off before working I removed the old element and disconnected the old element from the wire connections.I then installed the new element by connecting the terminals to the wire connection in the range before screwing the old retaining clips to the back of the oven compartment wall.Then I flipped the breaker switch back on and turned on the oven dial to 425 degrees to see the element heat up and glow red affirming the success of the repair.Total time to repair about 15 minutes.

Unpluged old one pluged new one in. So good to have a burner that all the coils heat up.

Got the shipment. Took it out of the package. Set it into the stove top. Tested to see if it worked, It did. Turned it off and took my dog for a walk.
Great company. Makes it easy for me order.

The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.

After a brief discussion with CS about the electric stove part was shipped it arrived and I proceeded to install I found it needed to be installed sideways not up & down like the old one. The terminals did not line up so I put the black lead first and the purple lead last in doing that I burned out the switch??? was not easy to install as the video showed his switch matched each wire? My installation was sideways??

This was my first time ever working with electrical issues. My husband is not physically able to do repairs now. Very easy fix. Just viewed video repair instructions and it went exactly as instructed. Within 45 minutes, I had my stove repaired and cleaned and back in working order!! Great results. My range is working perfectly again and Mama is happy!!