WWEF3000LWB Westinghouse Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- RAYMOND from JONESBOROUGH, TN
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Burn into
Remove the old one and replaced the new one. It was very simple, fast, and easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from CLEVER, MO
- Parts Used:
- 316075103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Bake element cracked and stopped working
Repair was so easy, Just remove the two screws one on each end of element slowly pull element towards you till you see the ends. Carefully
unplug the wires and then reinstall the new one and put screwes back in and you are all done
unplug the wires and then reinstall the new one and put screwes back in and you are all done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from KLAMATH FALLS, OR
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Bake element burnt in half
All that was needed was to unscrew two screws holding it to the back of the oven and pull it out to get to the wires. Then unhook the wires and install new one. Less than 2 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from WESTMINSTER, MD
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
No oven heat, but the broiler worked fine. All top burners worked.
Removed the oven heater and checked with an ohm meter. It read 'open', so I ordered a new element. It came in a few days, and my 16 year old grandson installed it, and all is well!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BILLY from JACKSON, MS
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burned element !
replaced the element !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from ALBANY, OR
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Socket set
Burned out bottom oven element
Undid 2 screw nuts holding the element to the back wall, with a 1/4" socket. Pulled off the two wires, pushed them onto the new element. Screwed the two nuts back on the rear wall. Done! Easy, worked 1st try.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sherry from JAMES STORE, VA
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Bottom oven element was burnt out
Unscrewed 2 screws, used pliers to pull off push on terminals attached to element . Slide terminals back onto new element and replaced screws. EASY
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Albert from STUART, FL
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bake element burnt out and snapped and appeared to try to arc-weld itself back together?!!
Just followed the very simple video instructions…it took less than 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rose from BADEN, PA
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
element in oven shorted out and started on fire
really easy unscrew the element from the back of the oven unclip remove old one slide clip on the new one and screw back to back of oven. Took 10 minutes or less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Goddard, KS
- Parts Used:
- 316075103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
oven wouldn't heat
using a nut driver I removed to two screws that were holding the element in place. Then simply disconnected each wire. Removed the old element and plug the new wires onto the new element. Reinstalled the two screws and everything works fine
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Victor A from ATTICA, NY
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burnt bake element
open the door take out the racks.unscrew the holding screws for the element,pull it away from the back wall of the oven. take off the wires carefully and reverse the procedure
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from MILTON, PA
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Oven did not heat
I watched your how to video and used my voltmeter to check my baking element. I found it defective and ordered your replacement. 5 or 6 days later it arrived in the mail. I installed it per the video and my wife baked a pizza to try it out. Perfect! Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- carol from LAUREL, MD
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bake element burned through in one spot; oven would not heat
replaced the element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marion from NEWPORT, TN
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
It burned out. Broke to peaces
I watched a YouTube video. Than it was easy. I turned the breaker to range off. Took the nuts off. Uncliped the part. Plug new part in. Put screws back in. Flipped on the breaker. And it works wonderfull.
Was this instruction helpful to you?
Thank you for voting!