WGF350ESC Westinghouse Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Eileen from AKRON, OH
- Parts Used:
- 316400603
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replacement of bottom oven panel
Very simple. I removed the oven racks, loosened the two screws that held the old panel in place, lifted out the old panel and replaced it with the new one, then tightened the screws to hold the new panel in place. It took no more than 10 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Maria from NEW ORLEANS, LA
- Parts Used:
- 316400603
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven bottom panel
Unscrewed old panel/removed and inserting new panel and used same 2 screws to secure in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from MERCERVILLE, NJ
- Parts Used:
- 5303935059
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Igniter failing to energize even though there was 120 volts being supplied.
Slide Range away from wall, unplug Range, remove rear cover (4) screws, removed burner assembly (5) screws, unplugged Igniter connector, loosen Igniter bracket, remove Igniter (2) screws. Reverse process to install new Igniter. I also wore latex gloves to prevent touching graphite portion of Igniter. Tested Broiler for operation, slid Range back into position. All good.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from LAKEWOOD, OH
- Parts Used:
- 316575500
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken oven door cap.
Watched a video - piece of cake!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barry from MOORE, OK
- Parts Used:
- 316400603
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Panel finish ruined by tin foil
Removed both oven racks the removed two screws in back. Lifted rear of panel until front lip of panel was free. Installed new panel in reverse order. I was recycled the old steel panel at our local recycling station.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- santa from glassboro, NJ
- Parts Used:
- 316490001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
temp was not reading right
remove back panel took out old part splice wire replaced
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert R from Lewistown, PA
- Parts Used:
- 316135702
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Two of theTop gas burners would not spark
Took 6 screws out holding the top on from the sides. Lifted the top front, popped out the spark module, Took 6wires off & reversed the processed to install the new one. I was really amazed when I ordered it Wednesday and it arrived on Friday. Believe me I bookmarked this site.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Saint Clair Shores, MI
- Parts Used:
- 5304515659
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Sliced Outlet Cord
I was replacing a range oven hood, so I pulled the oven away from the wall but left it plugged in. I removed the old oven hood, which had an exhaust pipe that was still mounted through the cupboard. While I was preparing the new oven hood the exhaust pipe fell out of the cupboard and cut the oven wire in half. I was able to find the part number on the existing cord and looked up on line. I ordered the part using 3-5 business days and it showed up in 2 days. I was able to attach the new cord, which had an easy clip plug, and secure back to the stove. Very easy and very inexpensive to do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Durham, NC
- Parts Used:
- 316400603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Aluminium foil fused to the panel
I removed the two back screws, slid out the old panel, then fitted in the new panel (it fit perfectly) and replaced the screws. Five minutes, tops.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David C from Huntington Beach, CA
- Parts Used:
- 316490001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Temperature not correct.
Pull out stove. Unplug power. Remove four screws on each corner and loosen one screw in the middle. Remove back panel. Locate and unplug sensor connector. Remove one screw from sensor plate. Turn the sensor 45 degrees and pull sensor out from the rear. Connector received had the incorrect plug and terminals so it was necessaary to splice the connector from the one removed to the one received. Cut and splice wires as necessary. Install sensor, install back panel, plug in electrical power, push stove back into position. I used a temperature gauge to check temperature after stove was in position. In my case the temperature had to be adjusted which is a keyboard function on this unit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from AuGres, MI
- Parts Used:
- 316489400
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
oven would not stay on
remove belly pan ,pull draw out easy acsess remove screws and replace
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from Mansfield, MA
- Parts Used:
- 316490001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
oven would turn on and stay on regardless of set point
Pulled oven from counter space unplugged unit unscrewed 9 - 1/4" tech screws then one more 1/4" tech screw that holds the sensor.Inserted the new element cut the two wire because it was a different connection stripped the wires and did the same to the old element but used the old plug.Connected the plug,plugged the over back in slid the unit back and turned out on for a test.All is well,thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doug from Charlotte, NC
- Parts Used:
- 316220000
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Knob on gas range wore out
I just slapped the new one on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vernon from Moorehead, KY
- Parts Used:
- GRLP3
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
bought a used gas range i have propane it was natural gas
changed the orfices with a 10mm socket and driver handle used an adjustable wrench to tighten the orfice in the bottom of the oven approximately 45 minutes we were using the range
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ed from petaluma, CA
- Parts Used:
- 316400603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
replace lower oven floor
removded 2 screws at rear of panel, moved panel toward rear of oven, lifted up and out. Slid in new panel in front groove then lowered onto oven floor and secured it with the 2 screws at rear of oven.
Was this instruction helpful to you?
Thank you for voting!