WEF360ESB Westinghouse Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Larry from Cowgill, MO
- Parts Used:
- 316075103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Oven element burnt in several places
Just followed the same instructions that the other people did when replacing this element. Was very easy to replace . Just turned off the power , rwemoved the two nuts , pulled the wires out about 3 inches and unpluged old one and pluged in the new one, replaced the nuts and volia ,DONE
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Hagerstown, MD
- Parts Used:
- 316075103
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Oven would not heat up-
Disconnected the main electrical plug from the wall for the oven..
Used a nut driver to remove the two screws that held the heating elementin place.
Pulled the element out so I could remove the two wire terminals.
Installation of the new heating element was fairly basic..Oven is working great..
Used a nut driver to remove the two screws that held the heating elementin place.
Pulled the element out so I could remove the two wire terminals.
Installation of the new heating element was fairly basic..Oven is working great..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MIRANDA from INDEPENDENCE, KY
- Parts Used:
- 316075103
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Element Was Sparking And Coal Hot Red
Unplugged oven, pulled out old element, reattached new one, making sure to be careful with wires, and put on as secure as possible, just like it was before. . . Very easy to fix
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- don from whiteville, NC
- Parts Used:
- 316075103
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
bake element burnt into
i removed the back panel removed two screws pulled the element out
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Campbell, CA
- Parts Used:
- 316075103
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Bake element broken
Removed screws. Tried to pull out old element but spade lugs on old element were bent at ninety degree angle. Once I figured that out I was able to manouver the old element out with the attached wires. Had to be carfull that the loose wires did not slip back ijn through the hole. Reaching in over the oven door was a but diffcult, but all-in-all the jobe was done in a few minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- lynne from pelham, NH
- Parts Used:
- 316075103
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Socket set
bake element had stopped working
My husband had recently moved out of our house so I was very nervous about trying this repair myself but it was actually very easy!!I ordered the part on Monday, it arrived on Wednesday and Wednesday night I was baking dinner in the oven!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Orefield, PA
- Parts Used:
- 316075103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Original Elememt went bad
The directions have been stated many time and they are quite simple. Take out the two screws, pull the element so the wire connections come through into the oven. Disconnect the element at the wire connectors and replace. This is a dirt easy job.
The only real area for a potential problem is pulling the wire connectors through into the oven. As long as you pull slow and from the back - right next to the whole, you will be fine. Take the connectors off carefully and you're golden. Easy job.
The only real area for a potential problem is pulling the wire connectors through into the oven. As long as you pull slow and from the back - right next to the whole, you will be fine. Take the connectors off carefully and you're golden. Easy job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Edina, MN
- Parts Used:
- 316436001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Large front burner would not come on under setting of "3"
Replaced infinite control very easily.
Was this instruction helpful to you?
Thank you for voting!
Baking element broken on one side
First I turned off the electical supply to the oven.I unscrewed the nut bolts on both sides of the baking element and pulled the wires through. Disconnected the wires of old element, then connected the wires of the new element. Pushed wires back and connected the nut bolts to the back of the oven.The new element did not come with new screws so I used the old screws to connect the new element. The only problem is that after installing the new element my oven still does not work. It doesnt get any heat. Not sure what went wrong.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Angela from Ruidoso, NM
- Parts Used:
- 316075103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
While baking cookies I looked in the oven only to find the bake element was glowing white on the curve of the element, then a second spot started to burn. The element was fried.
The repair took less time than finding the model number. After unplugging the range and allowing it to cool I disconnected the element (2 screws), went online and found Part Select ordered the element and saved $16.00 dollars over the least expensive local shop, I was amazed at how fast the element arrived, I believe it was 4 days from order to my door. I went to my local hardware store for some new connectors for the wire, put them on and plugged in the element fastened down the two screws and went back to baking cookies. The element was well and safely packed and came in perfect condition. It works like a charm. Thank You
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- raymond from irvine, CA
- Parts Used:
- 316075103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
oven not heating up
ordered new heating element, arrived promptly as expected, compared new heating element to old one and it matched in size only diameter a little different, removed two sheet metal screws holding element in place and pulled out element to expose conductors and removed them with screwdriver. Installed conductors on new heating element slid into holes and installed screws, turned power back on(first step is to turn off power) turned on oven to preheat and she worked like a new one. Thank you PartSelect. Saved me a bundle,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Browns Mills, NJ
- Parts Used:
- 316075103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bake element broken
turn off power to oven at breaker box
remove screws holding bake element in
pulls wires off old element
put wires on new element
put the screws back in
turn the power back on
remove screws holding bake element in
pulls wires off old element
put wires on new element
put the screws back in
turn the power back on
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from CLEVER, MO
- Parts Used:
- 316075103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Bake element cracked and stopped working
Repair was so easy, Just remove the two screws one on each end of element slowly pull element towards you till you see the ends. Carefully
unplug the wires and then reinstall the new one and put screwes back in and you are all done
unplug the wires and then reinstall the new one and put screwes back in and you are all done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- janet*hubbard from Old Town, FL
- Parts Used:
- 316075103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
oven not heating
slid the old one out and slid the new one in.turned the unit on and it works
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DAVID from PEACHTREE CTY, GA
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Oven element broke
Since I had the element out I cleaned the stove. That took me 2.5 hours. Used cold spray and let sit for two hours and wipe out clean took about 30 minutes. Now for the element itself it took me about five minutes to put the new one in. Oven looks and works like new. Just google your repair needed and watch the video. Easy Peasy. Last time I had it done by an electoral repair person for the tune of about $100.00. This time I bought the part and did it my self. Cost less than $25.00 including tax and shipping. No brainer.
Was this instruction helpful to you?
Thank you for voting!