MEF301PBDD Uni Range - Instructions

Shut off power - throw breaker. Oven access easier with door removed - requires removal of two Phillips head screws. Remove two screws holding element in place using 1/4" socket. Pull element & wires out and pull slide in connectors out (had to hold the wire end with needle nose pliers}. Installed element by reversing the removal procedures. Also good time to clean oven.

Just followed the instructions

I watched the video of the repair. It was very easy; removed 2 screws; disconnected 2 push-on tabs; removed the element; and then reversed the operation. Be sure to turn off the circuit breaker that powers the oven before you start the repair. Turn it back on when finished and test the oven.

Turn off power, remove heat coil assembly and drip pan. Unscrew the terminal assembly from the range top. Cut back 3 inches on each terminal wire and strip insulation 3/8 inch. Terminal assembly should be with the short side of the black block (from the side securement hubs) facing toward the coil stems. Slide the shrink wrap onto each wire and Twist each old with each new wire using the wire nuts and slide the shrink wrap Over each. Using a hair dryer, heat gun, or open flame carefully shrink the wrap. Secure the terminal back in place on the range.

I simply followed the instructions in your video. i shut down the power to the oven via the breaker panel, removed the two quarter inch screws with a nut driver, pulled out the old element exposing the two wire leads,disconnected one lead at a time and duct taped each lead to the oven wall,. Then removed the old element and replaced the new one in reverse order. Voila! It works great. This is the second element I replaced in this oven over the years. This site was prompt on shipping the new element (about 3 days since I ordered on a Sunday).. It was well packed and arrived on time and I even got an e-mail letting me know it arrived! How cool is that?! I've been a customer for a few years now and plan to be a "forever" customer. Thanks for saving the day! You ROCK!

Unscrewed screws in back of oven holding element. Slipped old element off of wire. No need to cut wires has the kind of ends (spade ends I think they are called) that just is pushed on to element. Attached new element. slid wires back into wall of wire rescrewed to oven wall. Very easy just be sure wires don't get pulled back into back wall of oven. Don't know what you would do then.

Turned off power to appliance removed the screws connecting the element. Disconnected the wires from the old element connected the new element replaced the screws and tightened turned power on turned power back on heated oven to be sure it worked. Very simple to do.

I looked for the proper part on this site. I was even able to find a video on how to install the part. It was great to see the step-by-step directions and tools needed. I ordered the part. It came quickly so that I was able to get my oven repaired before my kids came home for spring break. The only problem I had was the old screws were really stuck on. I used some WD-40 and they were still quite stuck. I learned that by gently going back and forth with the nut driver, rather than just trying to turn in the correct direction, that the screws came out quite easily. I felt so proud to be able to fix my own stove and save money in the process! Very satisfying for a single mom. Couldn't have done it without the video directions.

raise top of stove unplug burner plug in new one done

Sat on floor, pulled drawer out, inserted new clips, remounted door, stood up, high-fives myself.

Pulled out the old, and replaced. Very simple for a 62 year old woman! I cook a lot, being from the country, and Imwas so excited to get my burners fixed! Should have done it years ago! Thanks!

Remove drawer. Insert new slide. Install drawer.

this bake element has two special Hex style screws, securing it in place, but a nut driver worked just as well. remove the baking racks, and then loosen the two hex screws. slowly pull the element out of the back wall and then disconnect the electric leads. reinstall by doing then the opposite action. could not have be simpler.

The simplest repair ever! I just snapped it in and put the drawer back - fixed. I hope I have other repairs this simple.

Your website is great...easy and it literally took me no mote than 5 minutes to find what I needed and order...and received it VERY quickly. Must say I was dreading going to some parts house that we have in our town in bad area, and searching on dusty shelves for what I needed...am so glad I found you!!