MEF303PGWA Uni Range - Instructions

Turned off power at the circuit box. After locating 1/4" nut driver (the hardest part of the repair)I removed the oven racks. Took the opportunity to wipe out oven. Removed the two screws holding the element in place.Pulled element out gently to expose the connections. Wiggled the terminal connector off the terminal on element. Gave the wire a little bend to keep it from pulling back into frame. Repeated process on other side. Removed new element from wrapper. Placed element on oven floor, reattached terminals--making sure they were on snuggly--carefully slid terminal ends back though slots in oven body. Lined up brackets, reinstalled screws, replaced racks and turned power back on. Turned oven on it worked. Made cookies! Very easy repair.

Removed old elements I stalled new ones

Just placed the chrome bowl trays in place and was good to go. They look very nice.

I started to smell burning electrical smell from the burner area and heard a "buzzing" sound from the burner control while the burner was on. Pulled the element and noticed that the wire coil end of the left element was burned and pitted from arcing.
Pulled the range top up, used a phillips screwdriver to remove the terminal block clip from the range top. Upon inspecting the burner terminal block, I saw the brass wiper was missing from one side of the left slot, and there was considerable heat damage around the slot opening.
The terminal block being replaced was already replaced earlier for the same problem. The appliance repair folks recommended that we use light cookware on the burner. Instead, ensure both element leads are fully inserted into the terminal block.
I turned the power off at the breaker, used a utility knife to carefully slit the heat shrink tubing on the existing replacement, unscrewed the ceramic wirenuts, removed the old block, straightened out the range wires, slid the new heatshrink over the range wires, then twisted the new terminal block wires to the range wires. Screwed on the ceramic wirenuts, slid the heatshrink tubing over the wirenuts, and used matches to shrink it tight.
The package contains an instruction sheet with simple instructions.
Once the new terminal block was installed and the element terminals were fully seated, the "buzzing" from the burner control disappeared.

my husband did the repair.He unplugged the stove removed the element and installed the new element.plugged the stove in and checked operation of element.Stove works great

Pulled out the range, unplugged it and removed the upper back panel. The switches were held in place with two screws. Removed the old switches, detached the wires and plugged them into the new switches. Mounted the new switches, replaced the back panel, plugged the range back in and pushed it back into position. Appliance repair company wanted $370. I did it in 45 min. for less than $100.

Unplug range, remove top back panel. Remove knob. Replacement part is different, but if you look closely, each metal tab has a number stamped on the plastic housing directly beneth it. Remove old switch (2 screws)and remove and replace wires one at a time. You will need to cut the "one size fits all" metal shaft that the knob attaches to. We had to remove most of it, leaving only 2 "segments". File rough edges and apply vaseline so that the plastic sleeve will slip right on. We used the shorter sleeve (only 2 that are supplied will fit the knob). Replace unit and screw in. Replace knob.

It was a replace racks not repair. No problem

The replacement racks were spot on and the service was outstanding. had the racks in 2 days. Happy Happy Joy Joy! :)

Simple Just plugged it in !

Just took the old one out & put the new one in . Just a few screws to remove & put them back when replacing to new broil element , and were back up and cooking :)

Unplug the stove or disconnect at the breaker. Open the oven and remove the bake racks. Using a nut driver (or Phillips Screwdriver) remove the screws (one per side) that secure the bake element. Place them in a safe/secure place outside of the oven. Carefully pull straight back on the element until about 3 inches of the wire, that connects to the element, is exposed. Carefully unplug the wire from each element (make sure that the wire does not pull back into the oven insulation. I placed a small metal clip on each wire). Remove the old element and plug the new one in. Put everything back in the exact same way you took the old one out. Power the oven up and preheat your oven. Monitor this - should be no problem at all. Very simple process. My first attempt at this and it was very easy.

Watched the video

It was really easy just unplugged it took off the back cover changed the part out put back cover on plugged it in and the elements were working great!

Pulled stove away from wall and unplug .Removed grates for better access. Unscewed element scews removed element & tested for continuity.there was none element is bad . Replaced with new one . Time about 20 minutes.