CE30C8DFAA Tappan Range - Instructions

There is an installation video , but it was so easy, and if you clean your drip pans from those inevitable spills you can do this. I have zero mechanical abilities and I did. The website makes it easy to find your part, and the original literature you got with your appliance will direct you where to find the Model # and serial # on your Frigidaire Range. Order your part on line, get it in the mail and insert the Element yourself.Very happy with my transaction.

First I cut the breaker to the oven. Then pulled racks out of oven. Then used my nut driver to take the two screws of the back mounts. I then pulled the broken part out and installed the new one. I was not sure at all about doing this until I read some of your other testemonies, but after that, I became an oven repairman. The very next day after instalation, my wife cooked me a ham and a pan of cornbread! Thanks for the fast service, y'all got me back to eating my wifes homemade dinners within three days of ordering my part. There is no way to thank you for that, but here is a very large THANK YOU! I will definitely be back(hopefully not soon!) when I need other appliance parts.

Took out bottom drawer and unplugged power cord, slid unit out to reach back panel,removed front door( 2 Phillips screws) making it easier to reach back of oven, removed screws inside of oven holding element in place, took plate off rear and removed the spade connectors with needle nose pliers. Slid new element into oven and replaced screws inside of oven. Connected the two spade wires on the back and replaced rear panel. Slid unit back in place and plugged the 220v power cord back in. Straightforward and very simple! It took 3 times longer to clean the oven while it was disconnected than it did to replace the element.!

Pulled out the old drip bowls and replaced with the new. A simple snap!

It was simple.............the range-top tilts up so I proped it with a stick of wood, pulled out the old burner and plugged in the new one (when I saw how inexpensive the new element was I orderd two to replace the other 8" because it didn't look long for this world either). The whole operation took less than 10 min. no tools or batteries required!!!!!!!!!.........no-mus-no -fus.

Your prices were the lowest I found on-line, keep up the great work!!!!!!!!!

Removed the old & simply inserted the new one

Just replace the parts. Too easy for an old man.

I pulled out the stove from the wall and unplugged it. I then used a socket set with a long extension which made it easier to reach the rear wall of the stove. After removing the screws i gentle pulled the element forward and exposed the clips and wires. I removed the clips. The wires seemed to want to slip back into the hole so I used clothes pins to hold them in place. After I received the new element (Two Days) I reversed the process. Using a socket set it is very easy to tighten the screws to much. Be careful to just snug the screws. I plugged the unit back in and slid it back in place and turned it on.

Removed element by loosening two screws, disconnected heater element and connected new element and reattached to oven wall. Turn on oven to check for heater to work. Confirmed heater worked. Repair complete.

First unplugged the stove, then removed the screws holding the element in place. Next I pulled the element out until the wires were visible and unplugged them. After removing the old element, I plugged the new one in and positioned it with the screws. Plug the stove back in and done.

Oven is an in the wall unit. Normally it is an unplug and plug in. The old one had a melted connector, so the connector had to be cut off and replaced as well. Be sure to turn off the electricity at the braker to be safe, first.

If I didn't need my oven ASAP, I would not even have attempted to do this repair before my husband came home. But he wasn't going to be home for hours, and I needed it now!
First, I took off the back panel. Slid off the wire connectors. Then moved to the inside of the oven and unscrewed the two screws that secure the element to the oven, and pulled the old one out. Put the new one in and reconnected the wires from the back, and replaced the back panel.
That was it! It worked great!! Very simple.
I called my husband immediately to tell him of my great accomplishment!! I was so proud of myself!

Thanks,
Vicki

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires, replaced witht he new element

Removed the racks first. Then removed the two screws that held the element in place.
I then pulled the element out about three inches
exposing the connecting wires.Each wire has a female slide type connector just disconect each one and then connected the new element .
Attach new element by reptacing the two screws.

I watched my husband do this repair so if it happens again I can do it myself. He removed the screws holding the element in place, unplugged the element, plugged the new element in and replaced the screws. I am so glad I found your site. The posted pictures and measurements made finding the exact part a breeze and the element arrived in a couple of days. We saved a bundle!! Thanks.