30TESKWED2 Tappan Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Louis from GAINESVILLE, FL
- Parts Used:
- 316075103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Bottom oven element non-functional
Shut off power - throw breaker. Oven access easier with door removed - requires removal of two Phillips head screws. Remove two screws holding element in place using 1/4" socket. Pull element & wires out and pull slide in connectors out (had to hold the wire end with needle nose pliers}. Installed element by reversing the removal procedures. Also good time to clean oven.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from BIRDSBORO, PA
- Parts Used:
- 5303131601
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
oven door not closing completely
older range required no tools to repair, pulled old gasket out of notches at bottom of door, popped clips out of pre-drilled holes, folded new gasket ends {2 inches} and pushed into door, pushed clips into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from LAUREL, MD
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Bake element burned out
This is an easy repair, as described in several other replies. One important addition to what has already been described. Very important to turn off the breaker or unplug the range. One terminal of the range is connected to a hot wire and the range housing is grounded. You may not manage to electrocute yourself, but you could cause and arc that damages the housing or connector. Turn off the power. Beyond that, simple. Unscrew two 1/4" screws with a nut driver, slide the element out and disconnect the wire connectors. Reverse procedure to install the new element and turn the power back on. Preheat briefly to burn off any odor. Very easy repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from COFFEYVILLE, KS
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
broke
took out the old one, screwed in the new one. very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dave from LOUDONVILLE, OH
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Oven element burnt out.
Remove 2 screws. Pull element out. Slide 2 wires off. Just do in reverse it's done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Irving from Germantown, MD
- Parts Used:
- 316075103
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Oven element broke
It took me more time to find the right tool then to remove and replace the element. If I can do it anybody can do it. Removed two (2) screws with a nutdriver. Detached the element replaced with new element and replaced screws. Easy job!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rebecca from ASHEVILLE, NC
- Parts Used:
- 318372210
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Heating element for a frigidaire stove top broke
Got the shipment. Took it out of the package. Set it into the stove top. Tested to see if it worked, It did. Turned it off and took my dog for a walk.
Great company. Makes it easy for me order.
Great company. Makes it easy for me order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- david from PERRY, ME
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bad element
Remove screws pull off wires and install new parts
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Amber from CARLISLE, PA
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake element (bottom of oven) burnt through and snapped in two
Unplug the oven, remove oven racks, unscrew 2 screws at the base of oven bake element, pull the terminals off the wire bases, plug terminals back in, put screws back in place, plug in oven and test that it works...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from McPherson, KS
- Parts Used:
- 316075103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
The oven went out, element wouldn't turn off.
It's a simple project. Remove old element and replace it with new one. Access is easy. Only one tool needed. What impressed me was how fast the part got here, like the next day after I ordered it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vincent from Bonita Springs, FL
- Parts Used:
- 318036310
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Knobs for the three timers on the appliance console deteriorateddue to age.
The repair was very simple and easy. All I hqad to do was remove the old knobs and attach the new ones. No tool was required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arlene from ERIE, IL
- Parts Used:
- 316442300
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Burner not heating up.
Unpluged old one pluged new one in. So good to have a burner that all the coils heat up.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jim from gorman, TX
- Parts Used:
- 316442300
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
high power awful smell
raise top of stove unplug burner plug in new one done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Earl from Elkin, NC
- Parts Used:
- 316075103
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Bake element wouldn't heat.
The problem was caused by the owner placing an aluminum catch pan under the bake element. The failure of the element was where it was in contact with the pan. The repair involved removing two screws pulling out the element to access the wires. The connectors were the pull off type so I just disconnected the wires from the old element and placed them on the new element, pushed the element back in place and replaced the two retaining screws. I suggested that the owner not place anything in contact with the bake element. Be sure to up-plug the stove plug before attempting repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Debbie from Mineral Wells, TX
- Parts Used:
- 316075103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Bake Element burned in to stopped working
Turned off power to appliance removed the screws connecting the element. Disconnected the wires from the old element connected the new element replaced the screws and tightened turned power on turned power back on heated oven to be sure it worked. Very simple to do.
Was this instruction helpful to you?
Thank you for voting!