30-2234-00 (07) Tappan Range - Instructions

Unplugged the oven
Removed racks and bottom plate
Removed two 1/4" fasteners on ignitor
Installed new ignitor with two 1/4" fasteners
Cut each wire on old ignitor one at a time and hook up using included wire nuts
Plug in oven
Test oven
If it works, put it back together

Opened box, popped bubble wrap :) put in drip pans. Was great! Having been looking for the correct ones for a couple of years!

No major hardware stores had anything close. One visit to you site was all it took. Parts were loose so we removed them and replaced.

Found replacement drip pans at partselect.com.
Ordered them and received them in 2 days.
installed the new ones and all is well.
Had I known it was this easy, I wouldn't have spent countless hours scrubbing the old pans with Brillo pads. Considering how much I spent on oven cleaner, scouring powder and steel wools pads, it was lest costly to just buy new ones. (and they look better too).
Thank you PartSelect.

It was pretty much a plug in. My husband had it done in a few minutes. I want to thank you for your great service with receiving the part.
The oven is working great and now I am back to baking.
Thanks for everything
Christy

Removed 2 screws to oven bottom
Remove one nut that holds gas rail deflector
Removed 2 screws that held Igniterto the fuel rail
Cut 2 wires to the Igniter
attached 2 wires from new Igniter using ceramic wire nuts (Suplied with new part)
Install same as removal

The oven igniter was working, the Sears repairman said by the phone the igniter was probley weak and not geting hot enough. Remove door ( 4 screws) Remove oven pan (4 Screws) remove burner sheld. remove lighter and cut wires. Install new. Remove storage drawer and splice new wires to the old at the back.

A friend replaced the new ignitor with the old one...very simple job.

I would like to comment on how fast the service was from when I ordered the part online to 3 business days later when the part arrived....very happy about how easy it was to order part and that the part was in stock and delivered so quickly. Thank you very much !! I will recommend Part Select to a friend that frequently orders parts.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I made sure I memorized just how the wires would re-connect with the wirenuts. I then re-assembled everything. Be sure to read all the instructions, especially how to properly install wirenuts. I was able to access the wire connections below the oven chamber through the drawer at the bottom of the range. This is an important detail.

Replaced the flat style oven igniter. Turn off gas and unplug oven. Removed the broiler drawer, cut wires, unscrewed oven igniter (using a small/medium adjustable wrench), connected wires, fastened new igniter to bracket, spliced wire, twisted together, plugged oven back in, turned gas on, turned on oven after a few minutes...worked great.

First I'll say the instructions and comments from this site were right on, making it easy. I slid the oven out and unplugged the electric. Opened the door, took out the racks, took out the two thumbscrews at the back bottom and lifted the bottom plate up and out, and lifted off the heat guard plate. I could then see and reach the igniter pretty easily (the flashlight helped). The igniter may have been replaced before because there were already wire nuts on the wires. I unscrewed the two screws using the nutdriver and noted which wire (top or bottom) went to which wire inside. Unscrewed the wire nuts and removed the old igniter. Used the old igniter to determine where to cut and strip the new igniter's wires. Connected the wires of the new igniter using the wire nuts and put the two mounting screws in. Then just put all the other stuff back in (heat guard, bottom plate/two thumbscrews, racks). Plugged it in and started the oven. Got a small amount of "crackly" noise initially (maybe because the igniter was new) but that went away and it's been working fine and quiet since. Very easy (well, perhaps other than being on your knees, leaned into the back of an oven for a couple minutes). Well worth the effort.

1. Unplugged unit and shut gas off.
2. Removed the oven door(2screws).
3. Removed the oven floor(3screws).
4. Removed heat dispersion plate(1bolt).
5. Removed faulty igniter(2screws).
6. Labeled and spliced wires.
7. Connected new igniter.
8. Installed all previously removed parts.
9. Restored power and gas to unit and oven
fired up in a matter of seconds.....Thanks

suspected oven ignitor,went to partselect website and saw
others had same concern and ignitor was the failed part.ignitor was not getting white hot just orange-not enough
voltage going to the gas valve to open it.ordered and replaced
ignitor.repair took about 20 minuets-oven repaired.

Figured out which part we needed by reading about others problems; Followed instructions & Presto = oven heats!!!! Didn't have any problems removing or replacing part.

After finding your page and using your trouble shooting guide, it was easy getting the right part and the video helped a lot. Removed the over rack- removed two screws to remove the bottom- two screws to remove the burner. Clipped the two wires to the old igniter and removed the burner from the oven,removed the two screws holding the igniter and installed new one. clipped the wires to length and renistalled the burner. Using the two wire nuts supplied put the wires togather and reinstalled the bottom. Everything went well lite first try with no poof sound. Just in time for Thanksgiving cooking. Got fast delivery of parts. Will uas again. Thanks Partselect.