Models > 37-1022-57-03 > Instructions

37-1022-57-03 Tappan Range - Instructions

Jump to:

All Instructions for the 37-1022-57-03
16 - 30 of 47
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Conan from Moline, IL
Parts Used:
5303935058
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Two burners did not heat
Pretty easy installation; you lift the top plate up and snip the wires maybe four inches away from the burner. Leave more wire than you think you need; once you get into it you'll realize you need more wire length than you think.

Then strip the remaining ends, twist them together with the provided caps, and use the heat shrink to hold it together. Remove the old terminal, replace it with the new ones, and you're good to go!

Remember to check that the wires are tight in the cap before heat shrinking, though. I had to get more shrink wrap in order to finish.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
jim from gorman, TX
Parts Used:
316442300
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
high power awful smell
raise top of stove unplug burner plug in new one done
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Karen from POPLARVILLE, MS
Parts Used:
318372210, 316442300
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
My burners were shot!
Pulled out the old, and replaced. Very simple for a 62 year old woman! I cook a lot, being from the country, and Imwas so excited to get my burners fixed! Should have done it years ago! Thanks!
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Chuck from EVANSVILLE, IN
Parts Used:
5303935058
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Terminal block was bad.
Cut the old block off tied new wires to hot wires . That easy!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Joseph from FREDERICKSBRG, VA
Parts Used:
316442300
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Burner would cutoff intermittently
Pulled out old burner/inserted new
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Kenneth from LANOKA HARBOR, NJ
Parts Used:
318372210
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Left an appliance on surface element and melted paint onto the element
Plug the new element into the space on stove
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Gerald from MAITLAND, FL
Parts Used:
5308010418
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Stem broken off old after market switch
Pulled control panel off front of unit and replaced switch wire for wire , went great because part sent was OME
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Robert from PRAIRIEVILLE, LA
Parts Used:
5303935058
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Original terminal degraded and faulty
Turn off power, remove heat coil assembly and drip pan. Unscrew the terminal assembly from the range top. Cut back 3 inches on each terminal wire and strip insulation 3/8 inch. Terminal assembly should be with the short side of the black block (from the side securement hubs) facing toward the coil stems. Slide the shrink wrap onto each wire and Twist each old with each new wire using the wire nuts and slide the shrink wrap Over each. Using a hair dryer, heat gun, or open flame carefully shrink the wrap. Secure the terminal back in place on the range.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Donna from UNION, OR
Parts Used:
5303935058
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
replaced terminal block for element
followed the video provided on line which was very helpful..
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Dan from CHEWELAH, WA
Parts Used:
316442300
Difficulty Level:
Very Difficult
Total Repair Time:
More than 2 hours
uneven heating
Repair failed because part did not fit. Offset between top of element and contact prongs was too small, so element could not sit flat.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Sharon from TEMPLE, GA
Parts Used:
5303935058
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Heating coils stop heating
Remove heating coils raise stove top unsrew terminal blocks cut wires assemble terminals strip wires twist wires together install wire nuts apply heat shrink lower stove top plug in stove repair complete.Thanks.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Brian from MENASHA, WI
Parts Used:
5303935058
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
2 burner elements not heating
Simple: Snip old terminal block off. Strip wires. Connect new Terminal block using twist-on wire caps (provided in kit). Mount to stove top with existing screw. TIP: Make sure you insert the wire lead into the terminal block the right way (not upside down). Otherwise burner element will not insert into terminal block properly.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jackie from Charlotte, NC
Parts Used:
318372210
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Left rear burner had a damaged burner prong.
I just had to plug the new burner plate in the receptical
and it works again very well.
1 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
MARK from LIBERTY LAKE, WA
Parts Used:
5303935058
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Range burner coil worked intermittenly
Unplugged range and cut wires on existing burner plug. Connected the replacement plug with the provided wire-nuts. Secured with provided shrink-wrap. Reattached burner plug to to range top, and plugged in the burner coil. Presto.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jeffrey from Pittsburgh, PA
Parts Used:
5303935058
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
Intermittent heating element function
Instructions included with terminal block assembly. Toughest part was to strip the insulator off of the old wires on the stove. I was originally going to just purchase one but after looking at the other terminal blocks and seeing the burnt insulation and some of the wire strands, I just replaced all 4. PartSelect customer sevice was very helpful to confirm the correct part number I needed for my stove.
0 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 37-1022-57-03
16 - 30 of 47