36-3690-23-03 Tappan Range - Instructions

remove the bottom storage door unhook 2 return spring check with flash light install support under the top cook door and open the top door slowly , remove 3 screws at the bracket slide out the hinge with springs and slide out the hinge from the door install the 2 springs the same way you take it out and reinstall bracket and screws and springs and your done just picture and remember the you remove and reinstall i did it and i'm not a handy man i got happy when i did it my self i said wow to my self if i called some repair guy he possible wil charge me at least $ 125 to $ 150 for 25 min job

first I removed oven draw for access, then removed the two screws with a nut driver, next removed the two wire nuts and the old element was free. Replaced new element in reverse steps of removing old and the new part ignited the stove within 30 seconds, but now I have no excuse for not fixing dinner!! Thanks for promt shipping, it arrived early than anticipated.

Really easy to do, did not have to bring stove out from the wall! Turn power off to the stove. Remove the lower drawer. Remove the oven rakes. With a slotted screwdriver remove two screws in back of bottom oven cover, use 1/4 inch socket to remove two screws in front. Remove bottom oven cover. You can then see the part to be removed which has two wires going into it, the unit looks identical to the new part which heats up and lights the gas grill for the oven. I cut the two wires from the old part, remember which is the upper and lower; remove two screws holding onto part. Wire new part remembering top and bottom. Push extra wire down into bottom drawer and then mount new part with two screws. Turn power back on and try oven. Lite right away for me so I knew I had replaced the bad part. Reassemble and Enjoy!!

After diagnosing the problem, I entered the Tappan Model #, found the part needed, and ordered from Part Select. On receipt (2 day delivery), I followed the instructions enclosed with the ignitor, and within 30 minutes, had everything up and running. Thanks PART SELECT!

First thing is I looked for videos on how to replace oven igniter to get an idea. Unplug AC cord and turn off gas valve.On my model I was not able to figure out how to remove oven door. You can still work around it without removing. Inside the oven, remove bottom cover. Remove 2 screws located in rear corners. After removing oven bottom cover, next is a burner cover. Remove 2 screws located toward front of oven using a nutdriver or socket. After removing burner cover , you will find oven igniter. Now remove bottom drawer. This is why its a bit difficult for others. Igniter has 2 leads. Laying down on the floor and reaching in to follow-identify where the 2 leads go to. Using same nutdriver or socket remove 2 screws that hold up the igniter. I cut the leads from the base of the old igniter so you will have some slack to work on when you reconnect the wires underneath. Install new igniter, run leads same way.Strip back about 3/8 in. wire, twist leads to proper wires and twist on ceramic wire cap that is provided. Make sure no bare wires are exposed! Now you can test.

AS YOU DESCRIBED IN YOUR YOU-TUBE VIDEO, THE OVEN IGNITER WOULD GLOW BUT THE OVEN WOULD NOT LIGHT. YOU EXPLAINED THAT THE PROBLEM COULD STILL BE THE IGNITER AND SO I ORDERED A NEW IGNITER AND THEN WATCHED YOUR VIDEO ON HOW TO ACCESS AND REPLACE THE NEW IGNITER AND THAT FIXED THE PROBLEM. I ONLY HAD TO CUT THE OLD WIRES ON THE OLD IGNITER AND MATCH WIRES WITH THE NEW IGNITER USING THE CERAMIC WIRE NUTS SUPPLIED, AND I WAS BACK COOKING AGIN. THANKS.

Remove drawer, remove oven door, remove hinge and pieces. Get the spring loose. Attache new hinge to frame, reconnect spring. Slide door back on hinges.

Removed oven door. (two screws)
Removed racks.
Removed oven floor. (two finger screws)
Removed diverter (V) tray. (one nut)
Removed small panel @ left lower back of oven
(1 screw) to access elect. power disconnect.
Disconnected power.
Removed element (two square drive screws)
Snipped and stripped old wires, connected new
with ceramic wire nuts supplied.
Installed new element, reversed proceedure.
Oven lights in 10 seconds. Wife happy!
Probably 40 minutes, could do it again in15-20
once you know what tools to lay out.

first i removed the bottom of the oven [inside the oven] ,the part was right there,i removed 2 screws and unpluged the wires,then i cut the wire ends off the old part and used the wirenuts that came with the new one to hook them to the new part,then put it back in place,put the screws back in put the bottom back in and was done

Removed oven door, removed oven floor. Unscrewed skirt with attached igniter and gas tube. Two nut screws hold igniter to burner. Remove old igniter and replace with new, reattach two wires with supplied wire nuts. Replace oven floor and door. Oven lit right up, pizza anyone?

First I removed the two screws that held the element in place. I then pulled the element out about 3 inches and disconnected the two wires nuts, (from last repair) installed new igniter. Not rocket science here.

My existing igniter glowed but the oven still did not light. I determined it was too weak to activate the gas valve so I replaced it. Simple fix, four screws, wire nutted the two leads. Fired right up, took about 30 minutes to replace.

Thank you, Thank you and thank you!!! I couldn't be happier and I save over $200 in repair. My repair was very easy after watching the video. I cut off the wire and ensure that the new one are attached into place. Placed all parts back and boom, the oven starts working a new.

1. Removed top over the oven burner.
2. cut the two wires conneted to the igniter about
an inch and a half.Noted which wire goes to the top of the igniter and which one went to the bottom.
3. unscrewed the igniter from the mount and
carefully pulled it from the oven.
4. put the new igniter wires through the hole.
5. mounted the igniter to the burner.
6. attached the new wires to the top and bottom old wires with the connectors that came with the igniter.
7. pluged the range back in and turned on the oven. Igniter works great.

Turned the gas and the electricity off to the gas range. Took the two large screws out in the back of the range holding on the first pan. Have to look for them. Took off the single nut holding on the second pan. Used nut drive #10 to take off nuts. Be careful you do not lose them. Took off inoperative unit. Cut wires to unit. Stripped wires which connect to range. Put new unit on and tightened nuts with nutdriver. Spliced wires together and put on wire nuts securely. Taped them to the wires. Put the second pan back, then the first pan. Turned on gas and electricity to test.
Worked fine. Found that the old unit was cracked and had a piece missing. Must use flashlight. Be safe.