31-2238-23-05 Tappan Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Donna from UNION, OR
- Parts Used:
- 5303935058
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
replaced terminal block for element
followed the video provided on line which was very helpful..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dominick from Greensburg, PA
- Parts Used:
- 5303051140
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Broiler element burned out
I removed the four screws holding the element in place and pulled the element out and disconnected the two wire. Installation was pretty much the reverse of the removal except, when I went to put the two screws holding the element to the top of the oven I discovered the holes were rusted out. I looked for inserts to put in the holes but every time I tried different inserts the holes got bigger. I finally realized the oven is just sheet metal so I moved the bracket about an inch drilled new holes and used self-tapping screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from LANOKA HARBOR, NJ
- Parts Used:
- 318372210
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Left an appliance on surface element and melted paint onto the element
Plug the new element into the space on stove
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marvin from MONTANA CITY, MT
- Parts Used:
- 3051162
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
guide was broken
Used a slot screwdriver to pry the old guide...clipped the new guide into its place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chuck from EVANSVILLE, IN
- Parts Used:
- 5303935058
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Terminal block was bad.
Cut the old block off tied new wires to hot wires . That easy!
Was this instruction helpful to you?
Thank you for voting!
Old drip pans had turned to rusty lace.
Unplugged elements. Removed old pans. Wiped out holes. Inserted new pans, replaced elements.
Was this instruction helpful to you?
Thank you for voting!
Rusted Drip Bowls
This range is probably 30+ years old. Still works great. Just needed to replace the Drip Bowls.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from FREDERICKSBRG, VA
- Parts Used:
- 316442300
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Burner would cutoff intermittently
Pulled out old burner/inserted new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from CHEWELAH, WA
- Parts Used:
- 316442300
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
uneven heating
Repair failed because part did not fit. Offset between top of element and contact prongs was too small, so element could not sit flat.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pam from OCKLAWAHA, FL
- Parts Used:
- 5303935086
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
Can't regulate burners
Didn't get repaired because I could not get the right parts to fix it. You would send me a part for the oven. The oven and burner parts are not the same
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from TEMPLE, GA
- Parts Used:
- 5303935058
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Heating coils stop heating
Remove heating coils raise stove top unsrew terminal blocks cut wires assemble terminals strip wires twist wires together install wire nuts apply heat shrink lower stove top plug in stove repair complete.Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from MENASHA, WI
- Parts Used:
- 5303935058
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
2 burner elements not heating
Simple: Snip old terminal block off. Strip wires. Connect new Terminal block using twist-on wire caps (provided in kit). Mount to stove top with existing screw. TIP: Make sure you insert the wire lead into the terminal block the right way (not upside down). Otherwise burner element will not insert into terminal block properly.
Was this instruction helpful to you?
Thank you for voting!