MEF303PCWB Tappan Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Brook from Flora, IN
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Lower heating element was out.
Open the oven door and removed a metal screw from each side of the element on the rear wall of the oven. Pull each side of the element out about 2-3 inches and you should see the terminal fitting with a spade type connector. Remove the connector from each side and discard the old element. Place the connectors on your new element and push it through the openings that the old element came out of. Replace each of the metal screws and you are done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Merle from Towanda, PA
- Parts Used:
- 318372210
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
element had been damaged
I unplugged the damaged element and plugged in the new one. It took less trhan 30 seconds and the unit worked just fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOANNE from IMPERIAL, PA
- Parts Used:
- L304430992, 316048413
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Burner rings did not fit.
The replacement rings were so easy to install, and the little clip to hold them in place is really smart. Made my old range look really nice again. I thought the cost for the four rings was a bit high but they were well worth it. Thank You
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony J from HAMMONTON, NJ
- Parts Used:
- 5303935058
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
the burner stop working
Just followed the instructions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arlene from ERIE, IL
- Parts Used:
- 316442300
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Burner not heating up.
Unpluged old one pluged new one in. So good to have a burner that all the coils heat up.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Conan from Moline, IL
- Parts Used:
- 5303935058
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
Two burners did not heat
Pretty easy installation; you lift the top plate up and snip the wires maybe four inches away from the burner. Leave more wire than you think you need; once you get into it you'll realize you need more wire length than you think.
Then strip the remaining ends, twist them together with the provided caps, and use the heat shrink to hold it together. Remove the old terminal, replace it with the new ones, and you're good to go!
Remember to check that the wires are tight in the cap before heat shrinking, though. I had to get more shrink wrap in order to finish.
Then strip the remaining ends, twist them together with the provided caps, and use the heat shrink to hold it together. Remove the old terminal, replace it with the new ones, and you're good to go!
Remember to check that the wires are tight in the cap before heat shrinking, though. I had to get more shrink wrap in order to finish.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Tallapoosa, GA
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Baking element burnt out and broke in my hand.
First I cut the breaker to the oven. Then pulled racks out of oven. Then used my nut driver to take the two screws of the back mounts. I then pulled the broken part out and installed the new one. I was not sure at all about doing this until I read some of your other testemonies, but after that, I became an oven repairman. The very next day after instalation, my wife cooked me a ham and a pan of cornbread! Thanks for the fast service, y'all got me back to eating my wifes homemade dinners within three days of ordering my part. There is no way to thank you for that, but here is a very large THANK YOU! I will definitely be back(hopefully not soon!) when I need other appliance parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- staci from pleasant hill, MO
- Parts Used:
- 5303051519
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
our oven wouldn't heat when we needed to bake something.
took the screws out and then put the new element in and that was all.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rebecca from ASHEVILLE, NC
- Parts Used:
- 318372210
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Heating element for a frigidaire stove top broke
Got the shipment. Took it out of the package. Set it into the stove top. Tested to see if it worked, It did. Turned it off and took my dog for a walk.
Great company. Makes it easy for me order.
Great company. Makes it easy for me order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- rosetta from COLUMBIA, VA
- Parts Used:
- 3051162
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
problem pulling out bottom tray on range
just put in slot
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Monty from WILKESBORO, NC
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Shorted out baking element.
Took out bottom drawer and unplugged power cord, slid unit out to reach back panel,removed front door( 2 Phillips screws) making it easier to reach back of oven, removed screws inside of oven holding element in place, took plate off rear and removed the spade connectors with needle nose pliers. Slid new element into oven and replaced screws inside of oven. Connected the two spade wires on the back and replaced rear panel. Slid unit back in place and plugged the 220v power cord back in. Straightforward and very simple! It took 3 times longer to clean the oven while it was disconnected than it did to replace the element.!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shirley from tulsa, OK
- Parts Used:
- L304430992, 316048413
- Difficulty Level:
- Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
ugly looking drippans
in order to install the new burner pans, my husband used a screwdriver to push back on the metal clasp. this allows the notch on the drippan to go into the groove on the stove.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Katherine from Roanoke, VA
- Parts Used:
- 316067902
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lacking oven racks on used appliance
Your website is great...easy and it literally took me no mote than 5 minutes to find what I needed and order...and received it VERY quickly. Must say I was dreading going to some parts house that we have in our town in bad area, and searching on dusty shelves for what I needed...am so glad I found you!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- steven from EPPING, NH
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
The bottom Heating element burned out.
I pulled out the stove from the wall and unplugged it. I then used a socket set with a long extension which made it easier to reach the rear wall of the stove. After removing the screws i gentle pulled the element forward and exposed the clips and wires. I removed the clips. The wires seemed to want to slip back into the hole so I used clothes pins to hold them in place. After I received the new element (Two Days) I reversed the process. Using a socket set it is very easy to tighten the screws to much. Be careful to just snug the screws. I plugged the unit back in and slid it back in place and turned it on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jim from gorman, TX
- Parts Used:
- 316442300
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
high power awful smell
raise top of stove unplug burner plug in new one done
Was this instruction helpful to you?
Thank you for voting!