72-3657-23-12 Tappan Range - Instructions

First unplugged the oven from the wall and then I removed the bottom floor of the oven by removing the two screws at the back. Then I removed the heat shield over the burner by remove the two screws at the front of the oven and removed the nut in the middle of the heat shield that was hold the shield to the burner. I removed the two screws on the flat oven igniter and cut the two wires on the igniter and pulled the two wires through the open in the bottom oven from the drawer opening. Mounted the new igniter and feed the two wire from the igniter through the open in the bottom of the oven, Stripped the two wires that I cut from the oven, twisted the new wires to the old, and put the wire nuts on. Last I put everything back together and baked dinner. Took ten about minutes and saved a thousand dollars because I was going to buy a new oven. Thanks, Partselect.

1 - I unplugged the oven/ stove connection.
2 - Removed 2 screws and lifted it out the floor of the oven.
3 - Removed the nut holding down the flame guard and lifted it out.
4 - Removed 2 screes that held igniter in place.
5 - cut the wires for igniter.
6 - Stripped new wires with the nuts connector.
7 - Installed new igniter with 2 screws.
8 - Put it all back together step 3 & 2.
9 - Plugged in the oven/stove connection.
10 - Turn on the oven and works perfectly.
11 - My wife and daughter happy and ready to bake.

Repair was easy. just unscrewed the old handle, holes measured correctly and screwed in the new handle.The only flaw was that it did not come with the two end caps,they have to be bought separately & the handle ends are sharp without them.

I removed the bottom of the oven and flame guard for access to the ingniter. I then replaced the ingniter. The oven works like new now.

replaced it

I cut the wires from the old igniter near where it said to. I then connected the new wires to the old ones, put it back on, the way I remembered it being assembled, but still won't heat up. I tried to get an enlarged detail of where I was working on, but I couldn't enlarge it from your website. My friend, who knows about electricity, worked on it for several hours last pm(He's an electrician), but could not figure it out with the scamatic that was on the range, because he was not there when I disassembled it,

Unplug appliance. Remove the bottom of the oven (2 screws in back of oven bottom), remove burner cover (2 screws in front and nut in center holding burner). Pull out the bottom storage drawer under the oven and unplug both wires from oven Igniter which are located in the back. One wire plugs into the gas valve and the second wire went into a connector that was on the lower left. I removed the screw on the back oven wall that held the burner so I could remove the burner for ease of work. Remove two screws holding the old igniter. The two screws holding the igniter to the side of the burner were stripped and they took a little time to remove but I replaced them with two new screws I had in my misc. screw drawer and had no issue. Cut the top wire and splice it onto the top wire of the new igniter using the porcelain wire nuts provided. Do the same with the bottom wire. Re-assemble and plug back in. Everything worked perfectly.

followed the instructions that come with the part. very quick and easy.

I exposed the ignitor through the inside of the oven and then removed the two screws that held it in place. I then cut the wires underneath the stove ans reconnected them to the new part with the wire nuts provided. It was a simple repair.

cut wires and removed the burner . Removed the ignighter and installed the new with nut driver. slipped the burner back in place and nutted the wires...Wallagh!!! fired right up...

Unplug electicity, Take out all inside pans, unscrew the burner arm, disconnect white power wires to the igniter. remover gas buner, detach the igniter and attach the new igniter to the burner arm. re assemble the burner arm, connenct the white wires to the white wires from the oven just below the igniter. Put all pans and guards back in oven, plug in and test.

Unplug electric , remove old igniter, cut wires, shorten new igniter wires, strip insulation, wire nut together, attach new igniter, plug in electric, fire it up. Worked great.

removed bottom plate in oven removed three screws and cut two wires.

After removing heat shield, removed heating element (make sure you have the right bit, I stripped one of the screws). Cut wires , making sure to mark them. Reconnected and it worked like new! Saved a bunch of money,thank you!

took out the old (2 screws) put clip on wires and put the new part in. Simple