30-2251-23-11 Tappan Range - Instructions

Ordered new racks and replaced them.

Twisted replacement bulb into place easily. Let there be light!

Removed oven door. (Open to first position then lift the door straight up). Located igniter in bottom of oven, followed connecting wires to connection block below oven behind the oven drawer. Disconnected the existing wires. Lifted the burner out of oven to disconnect defective igniter. Screws were fused to the burner. Used vice grips to remove screws requiring the screw holes to be retapped. Bought new screws to replace trashed screws. Installed new igniter to the burner rail then set burner rail back in place. Fished the leads from new igniter back down to connector block. Reinstalled leads. Reinstalled oven door. Tested functionality of oven. Everything worked. Reinstalled metal plates back in oven. Reinstalled cover over connection block behind bottom drawer. Reinstalled drawer. With the exception of fighting with two screws fused to the burner rail it is a very straightforward repair and shouldn’t take much more than 1/2 hour.

First of all I would like to comment on how it easy it was to place this order and I was pleasantly surprised that it was rec'd the next day. Also it was the correct part that I needed. To install it, first I removed the screws and then the metal that was holding the broken glass. Once the broken glass was removed, I set the new glass in the metal strips and basically screwed it back together. Please note to be careful to remember which screws go where as they are not the same size and do not fit anywhere but where they belong. That was the only part of the job that I had a problem with.

The repair went relatively easy especially after reading that another homeowner found the door to be "spring loaded". I was prepared and made sure I held onto things tightly.I removed the screws as I came to them and carefully removed the other 3 pieces of glass, finally reaching the inner panel. Putting that in and holding it as I put the next piece back was the most difficult. Once that was in place, the rest was just a matter of redoing what I undid. Needless to say, I was a bit nervous the first time I used the oven. No problems though, works like a charm! Thanks!

I'll be happy to tell you "my repair story!" I was so happy to find a site that carried the knobs for my Tappan range. I called Sears, where we purchased the stove some 15 years ago, and was told that the only way to get new knobs from them was to purchase a "completely new unit" - or in other words, a new stove!!! With nothing being wrong with my stove, I began searching online for a site that sold knobs and found the PartSelect.com site. I was very happy with the service that I received, but thought that the stove knobs were grossly over priced!! I also thought that it was strange that you would send 1 knob at a time, but as long as I got them all, I'm happy. Thank you.

It went very well. Very quick. Just took out a couple of screws, took out the rest of the broken glass, slipped the new piece in and screwed it all back together. This was the first time I had ever tried to fix any part of a range/oven before, it was very simple...

First I turned off the circuit breaker to the oven. Then, I removed the base of the oven (the oven floor) by easily removing two screws. I also removed the flame guard by removing a screw. That easily exposed the old oven igniter. I removed the two small screws that held that in place. The igniter is connected by two wires, which you'll have to snip. Snip those very close to the igniter (leave about an inch of wire on the igniter). Using a wire stripper, remove about 1/2 inch of the outer sheath of the existing wires. On the new igniter, snip the wires leaving about 2 inches still connected to the igniter. Using the wire stippers, remove about 1/2 inch of the outer sheath. Using the plastic wire caps that came with the new igniter, connect the wires from the oven to the corresponding wire on the new igniter. Screw the new igniter back in place. Replace the flame guard and oven floor. Turn on the circuit breaker and start cooking again!

get liquid wrench, remove oven door(2 screws) remove oven bottom(2 screws) follow directions included with part. unplug or shut off electricity at breaker panel, Have a good light source.

I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.

It was a replace racks not repair. No problem

The replacement racks were spot on and the service was outstanding. had the racks in 2 days. Happy Happy Joy Joy! :)

I looked in PARTS SELECT.COM immense inventory of replacements parts, found the right ones, order them, got in with in two days, replaced the old ones with the new parts, Now we are cooking!! Thank you.

Disconnected the oven from the wall outlet. Removed the bottom panel of the oven to reach the parts. Reached in the thight spot (not for a big guy)to unscrew the old igniter. Installed the new one. Plug the oven back. Turn the oven on bake at 350. Oveb lighted up in 5 seconds ! Working great since then!!!

First removed oven racks then two screws to remove oven door, removed two screw of oven fan cover, ( need to remove fan cover to have clearance to removed bottom cover of oven) removed bottom cover of oven, then removed two screws holding oven igniter and cut wires of old igniter then spliced wire of new igniter to existing wire and reassemble in reverse order.