TGF350MXDSC Tappan Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Barry from MOORE, OK
- Parts Used:
- 316400603
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Panel finish ruined by tin foil
Removed both oven racks the removed two screws in back. Lifted rear of panel until front lip of panel was free. Installed new panel in reverse order. I was recycled the old steel panel at our local recycling station.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from MERCERVILLE, NJ
- Parts Used:
- 5303935059
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Igniter failing to energize even though there was 120 volts being supplied.
Slide Range away from wall, unplug Range, remove rear cover (4) screws, removed burner assembly (5) screws, unplugged Igniter connector, loosen Igniter bracket, remove Igniter (2) screws. Reverse process to install new Igniter. I also wore latex gloves to prevent touching graphite portion of Igniter. Tested Broiler for operation, slid Range back into position. All good.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from LAKEWOOD, OH
- Parts Used:
- 316575500
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken oven door cap.
Watched a video - piece of cake!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from NORWOOD, PA
- Parts Used:
- 5303935059
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Replace igniter
New part needed to be spliced to old connector with porcelain wire nuts then removed lower oven drawer to access the connection for igniter
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Maria from NEW ORLEANS, LA
- Parts Used:
- 316400603
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven bottom panel
Unscrewed old panel/removed and inserting new panel and used same 2 screws to secure in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- santa from glassboro, NJ
- Parts Used:
- 316490001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
temp was not reading right
remove back panel took out old part splice wire replaced
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert R from Lewistown, PA
- Parts Used:
- 5304505695
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Two of theTop gas burners would not spark
Took 6 screws out holding the top on from the sides. Lifted the top front, popped out the spark module, Took 6wires off & reversed the processed to install the new one. I was really amazed when I ordered it Wednesday and it arrived on Friday. Believe me I bookmarked this site.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doug from Charlotte, NC
- Parts Used:
- 316220000
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Knob on gas range wore out
I just slapped the new one on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from AuGres, MI
- Parts Used:
- 5304534663
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
oven would not stay on
remove belly pan ,pull draw out easy acsess remove screws and replace
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Saint Clair Shores, MI
- Parts Used:
- 5304534377
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Sliced Outlet Cord
I was replacing a range oven hood, so I pulled the oven away from the wall but left it plugged in. I removed the old oven hood, which had an exhaust pipe that was still mounted through the cupboard. While I was preparing the new oven hood the exhaust pipe fell out of the cupboard and cut the oven wire in half. I was able to find the part number on the existing cord and looked up on line. I ordered the part using 3-5 business days and it showed up in 2 days. I was able to attach the new cord, which had an easy clip plug, and secure back to the stove. Very easy and very inexpensive to do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Durham, NC
- Parts Used:
- 316400603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Aluminium foil fused to the panel
I removed the two back screws, slid out the old panel, then fitted in the new panel (it fit perfectly) and replaced the screws. Five minutes, tops.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melanie from Reading, PA
- Parts Used:
- 316404500
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
lost a rack?
After removing an oven rack to make room for the thanksgiving turkey roaster, I have NO IDEA, where I might have stowed it away! After searching every cabinet and every closet I realized I needed to do something quick for our annual christmas cookie marathon that would begin on Sunday. It was so easy to order the part, it arrived the next day, and we baked for 5 hours using the 3 racks in the convection oven. Dozens of cookies later... Thank you Parts Select!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ed from petaluma, CA
- Parts Used:
- 316400603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
replace lower oven floor
removded 2 screws at rear of panel, moved panel toward rear of oven, lifted up and out. Slid in new panel in front groove then lowered onto oven floor and secured it with the 2 screws at rear of oven.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Suttons Bay, MI
- Parts Used:
- 316400603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Men Should Not Use The Oven
Delivery was fast. Two screws to remove the old oven panel. Slipped in the new panel and tightened the screws with my fingers. Job completed. It was as easy as that.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Provo, UT
- Parts Used:
- 316112005
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Needed to install an anti-tip bracket on my stove.
Moved the stove. Used the template to position the bracket. Put the supplied screws to attach bracket to the floor. Slid stove back into place. DONE!
Was this instruction helpful to you?
Thank you for voting!