72-3981-00-07 Tappan Range - Instructions

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires....install new element and woalla.........save thangsguivingday thanks to part select .com..........

Simple repair ,unplug unit,cut the 2 wires close to heating element,remove elements 2 screws w/1/4 inch nut driver. Cut and strip 2 wires back about 1/2 inch,be sure to cut wires close to element,wirenut both wires together. Reinstalled element,plug unit back in. Done . . . 12 Minutes,ready to bake a cake. .

First turn the thermostat off-cut the wires leading to the ignitor, close to the ignitor side-Remove the two 1/4" monting bracket screws and remove the ignitor install the new ignitor using the same 1/4" screws and reconnect the wires leading into the ignitor, note the polarity is not imp[ortant--use the heat temp-wire nuts provided--close the door and call for heat the gas valve is working fine now....

Read the instructions provided and simply installed the guides. Total time was less than 5 min.

open oven door remove bottom of oven then remome the metal cover over the burner to expose the ignighter remove 2 screws that hold it to the bracket. the two wire's that come out of the ignighter run down under the bottom oven pan, i removed the bottom front cover by lifting up and then pulled out, then i could see the wires i removed the wire nuts and pulled old wires off and removed old ignighter. i pulled off the insulator covers from the old one and slid them on the wires of the new ignighter then i fished the wires back down and and attachted them with the wire nuts, then reasembled the rest of the oven. woks great!

Removed lower drawer of oven and base panel of oven. Unplugged stove from outlet. Removed old igniter w/ nut driver (two screws). Disconnected wires (blade connectors) from stove base. Disconnected two-pole plug from oven after removing protective cover in corner.

Install new igniter. You will need to cut existing wires from old igniter so that spade and two-pole connectors can be reused. Join these wires with the new ignitor wires using the ceramic wire nuts provided with the new unit.
Directions are also provided with the new igniter.

CUT THE WIRES ON OLD IGNITER AND WIRE NUT THE WIRES OF THE NEW IGNITER TO WHERE I CUT THE OLD ONE OFF.

First I removed the two screws that held the element in place. I then pulled the element out about 3 inches and disconnected the two wires nuts, (from last repair) installed new igniter. Not rocket science here.

1. Removed top over the oven burner.
2. cut the two wires conneted to the igniter about
an inch and a half.Noted which wire goes to the top of the igniter and which one went to the bottom.
3. unscrewed the igniter from the mount and
carefully pulled it from the oven.
4. put the new igniter wires through the hole.
5. mounted the igniter to the burner.
6. attached the new wires to the top and bottom old wires with the connectors that came with the igniter.
7. pluged the range back in and turned on the oven. Igniter works great.

Used a slot screwdriver to pry the old guide...clipped the new guide into its place.

I removed the bottom of the oven and flame guard for access to the ingniter. I then replaced the ingniter. The oven works like new now.

Repair was easy. just unscrewed the old handle, holes measured correctly and screwed in the new handle.The only flaw was that it did not come with the two end caps,they have to be bought separately & the handle ends are sharp without them.

Removed the drawer. Inserted the new glide tab into a hole in the side. Inserted the drawer slides in the the glide. Closed drawer--done! Works fine. Probably only 5-10 minutes.

First unplugged the oven from the wall and then I removed the bottom floor of the oven by removing the two screws at the back. Then I removed the heat shield over the burner by remove the two screws at the front of the oven and removed the nut in the middle of the heat shield that was hold the shield to the burner. I removed the two screws on the flat oven igniter and cut the two wires on the igniter and pulled the two wires through the open in the bottom oven from the drawer opening. Mounted the new igniter and feed the two wire from the igniter through the open in the bottom of the oven, Stripped the two wires that I cut from the oven, twisted the new wires to the old, and put the wire nuts on. Last I put everything back together and baked dinner. Took ten about minutes and saved a thousand dollars because I was going to buy a new oven. Thanks, Partselect.

Unplugged the appl. I removed the bottom of the oven. Disconnected the two wires. Removed two screws that hold the element in place. Replaced it. And put everything back together. Since this element goes bad about every year an a half, I keep one on hand all the time.