31-2977-00-01 Tappan Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Beverly from Genoa, WV
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
the oven element went out
took off the back of the stove..first Unplugged it! and undid the old unit, and put the new one on....easy peasy!..Thanks for your fast mailing!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas C. from Mahnomen, MN
- Parts Used:
- 5303051519
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Oven baking element was burned out.
Moved stove out from wall and cabinets, then unplugged the stove. Removed the oven racks, then removed the 2 screws securing the baking (lower) element to the rear wall of the oven. Pulled the element out a few inches and disconnected it from the stove wires. Removed old element. Removed screws from rear panel to gain access to wiring. Inserted new element and connected to wiring. Put element in place and replaced the 2 screws in rear wall. Put rear panel back in place and replaced panel screws. Plugged stove back in and moved back into place. Tested oven and it worked just fine. Parts Select did a great job of filling my order and promptly shipping it. I got it in 2 working days.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from somerset, MA
- Parts Used:
- 5303051519
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Replaced the bake element
Removed the elments2 screws, unhooked the two wires, removed the rear cover from back. I then installed the new element, covered the termanals with electric tape replaced the rear cover screwed down the new element, tested.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jenniffer from Gresham, OR
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Old heating element quit working, smoking, sparks
took out the screws at the back of the oven, removed the old element and put the new one in, replaced the screws. The new part was mostly the same size as the old one, some of the angles were different and the ends slightly different, but it fit and works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Burkburnett, TX
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
Lower heating element not working
Loosened two nuts , removed old element. New element snapped into terminal tightned nuts . 0 minutes tops.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from Hayward, WI
- Parts Used:
- 5303051519
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven wouldn't heat.
I removed the 2 screws. Pulled the heat elemnet out. Disconnected the 2 wires. Then I connected the 2 wires to the new element. Pushed it back in. Tightened the screws and was sone.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rebecca from Withams, VA
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Oven would not heat
My husband completed this replacement in less then 5 minutes. He took out two nuts discounected the old element then replaced with the new element. Easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Temple, PA
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Bake element would not heat.
Removed two screws that hold the element in place. Pulled it out a few inches-removed the wires
& re-connected to the new unit. Screwed it back in place & i was done. It took about 10 minutes. The new unit works fine. Saved a bunch of money by not calling a repair man. Thank you very much.
& re-connected to the new unit. Screwed it back in place & i was done. It took about 10 minutes. The new unit works fine. Saved a bunch of money by not calling a repair man. Thank you very much.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peggy from Lykens, PA
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
heating element burned out
Just took the back of the stove off and removed old one and put new one in. Very simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Ocean View, AL
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
oven burner was burned out.
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I cleaned up the bottom of the oven since it is so much easier to clean while empty. Plugged the two wires onto the new burner, slid it back into position and refastened the screws.
The hardest part was getting one of the screws out since it had been rounded over and the phillips slots were worn too, like somebody had failed to remove it earlier. All I needed was a pliers to grip it.
The hardest part was getting one of the screws out since it had been rounded over and the phillips slots were worn too, like somebody had failed to remove it earlier. All I needed was a pliers to grip it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DUSTIN from OGDEN, UT
- Parts Used:
- 5303051519
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Element went out ...
Took the back off, and took the terminals off. Took out the old element and put the new one in and put the terminals on and screwed it back in and put the back on. And all done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- paul from roslyn, PA
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
haeting element cracked
juist loosened nut and pulled element out about three inches, detached leads, reattached new leads and installed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Ottumwa, IA
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Original heating element broke due to dripped food.
Unplugged the appliance then removed the two screws holding the element in place. Pulled it out about 2-3 inches then pulled the wires off. The replacement element has 90 degree connectors as opposed to the original 180 degree connectors but that didn't affect installation and hasn't affected operation. Slide the wires on the new element, slide the element back in the oven, screw it back in and you're good to go. Trust me, easiest repair to do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jakki from Loco, OK
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench (Adjustable)
Bake on the oven wont heat up, but the broil and the stovetop worked fine
I'm a stay at home mom so when the oven didn't heat up I through oh no I have to get a new one. Well who can afford to get a new oven right after christmas. So I played with it to see if the other parts still worked, when I found that they did, I googled the the Appliance name, that is when PartSelect showed up and they had a video on how to replace the bake element. It looked doable so I ordered the part and it really was a easy fix. It took less than 10min all I had to do was pull out the old element and put in the new element. Only trouble I had was, I had to bend the prongs alittle but that was no problem. Thankyou PartSelect
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from belton, TX
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
oven would not heat
took two screws out disconnected wires and connected new element ,screw back togather in about ten mins and started cooking dinner
Was this instruction helpful to you?
Thank you for voting!