TEF364ASJ Tappan Range - Instructions

Switch was easy to replace. Some hex head screws to remove the panel and two screws to remove the switch. Though the plug in positions were totally different, all the quick connect terminals were marked on both switches.

replaced it

I saw a chart of the oven door at site after I finally got the model number. I actually thought I had ordered the wrong part, third door in was last pane I thought, but actually this is inner most oven door, glass panel four. I had to find a correct screw diver which took awhile. I thought I didn't have the strength to turn the necessary screws, but easily could with correct screw driver. I followed other stories about removing handle, spring loaded door, so be careful it pops apart. A bit tricky to put back together, cause you have to hold door together against spring when you put cap on and door handle. Remove handle, remove top plastic cap. Will see screws holding glass and aluminum shield in place. Remove shield, need to remove screws holding glass two panes with holder. Shield pulls back and this glass just drops in. Reassemble door.

my dad and i did it together and it was easy. just had to remove the screws on the outside oven door pull the door apart, remove the old glass and put in the new and put the screws back in. hardest part was to get some of the screws out because they had been in so long.

The repair shop wanted 150 dollars to fix it. I ordered the glass and replaced it myself. It was really easy and all I need was a screwdriver. It took me about 30 minutes total.

Really a no brainer, but I do have to say that PartSelect customer service is excellent. My part was located and on it's way within a day and arrived a couple of days later.

Pull stove out to get behind it,unplug temperature probe plug. Remove temp probe from oven by removing the screw holding it in place on back of oven. Cut plug off temp probe unit leaving as much lead wire as possible on plug end. Strip wires on new probe and end of plug wires(one quarter inch). Then I used two small butt connectors to join the stripped wires,one for each pair of wires. Two small wire 'nuts' may also be used as the connections are outside the oven and not exposed to the heat of the oven while it is in operation. Hope this helps the inexperienced 'do it yourselfers'--:)

First I took the door off. Then I removed about a dozen screws. Than my wife insisited on cleaning the other two windows! Since the inside window was broken ;a lot of grease had gotten on the other two windows.She said she would never have another chance. After that I put everything back together. It took about an hour all together.

First I removed the oven door screws, then I removed the outer handle and then there were 2 more sets of screws that actually held 2 panes of glass onto the door.

First i removed the drawer. Then i removed the broken drawer glide and replaced it with the new one. Then i put the drawer back! The parts were a perfect match...

No problem..... I just had to slide the new one in..It took all of 5 minutes...
I searched so many different places for the part until a friend told me about Part Select!!!
Thank you so much...

We have an older .......range that came with our house when we bought it in 2000...the stove works fine (for an electric stove!), but the drawer was always problematic. Sometimes it would sit straight in the appliance cabinet and sometimes it wouldn’t. Sometimes it would flop up and down, sometimes it worked and sometimes it didn’t!

We lived with it for TEN years...then a couple of weeks ago I needed a pizza pan. I opened the drawer and the darned thing wouldn’t go back into the stove properly. I played with it for awhile, trying to figure out why it didn’t work correctly! After some energetic observation (accompanied by some choice words about American engineering!) I realized the front drawer guide was broken off!! It was one of those “Aha!” moments!!

I retrieved the plastic piece and went to a local appliance store to get a replacement. They said they’d order one (for 8.95 and I pay shipping and handling!), and it would take 2 to 3 weeks to get it! I declined their offer. Surely, somwhere on the internet there was a supplier who had this part!!

I sat down with my MacBook Pro and looked up “range parts” and was immediately directed to partselect.com. I looked up the part (which was ONLY $3.38) and ordered two. I had the parts in my hand in four days, and even with shipping paid less than half what the other place wanted locally.

I pulled the drawer out, literally dropped in the new guide, and the drawer has worked flawlessly since!! We are forever grateful for PartSelect and will always keep their address on top of our web vendors list!!

Give them a chance...the least you could do is save some aggravation, and maybe a little bit of money, too!!

It went okay but I had to have some help putting it back together. One person held the glass while the other person tightened the screws.

Fed ex dropped the part off at 7 one night, had it repaired by 7:05. Popped the broken glide off, popped the new one in. Easier than easy. Took longer to empty the drawer and remove it than to do the repair.

Took no time at all to fix and is as good as new. Hooray!