31-2377-00-01 Tappan Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jeannette from West Jordan, UT
- Parts Used:
- 5303051519
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Wrench set
Bake element broke
I just followed the instructions that I found online.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas C. from Mahnomen, MN
- Parts Used:
- 5303051519
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Oven baking element was burned out.
Moved stove out from wall and cabinets, then unplugged the stove. Removed the oven racks, then removed the 2 screws securing the baking (lower) element to the rear wall of the oven. Pulled the element out a few inches and disconnected it from the stove wires. Removed old element. Removed screws from rear panel to gain access to wiring. Inserted new element and connected to wiring. Put element in place and replaced the 2 screws in rear wall. Put rear panel back in place and replaced panel screws. Plugged stove back in and moved back into place. Tested oven and it worked just fine. Parts Select did a great job of filling my order and promptly shipping it. I got it in 2 working days.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Spencer, IA
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Wrench (Adjustable)
Oven wouldn't heat as element was burned out
I removed the two screws that hold the element in place. Then pulled the element out, disconnected the two wires. Reconnected the new elements wires, replaced the screws and the element was ready to go. Worked very well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- peter from edmore, MI
- Parts Used:
- 5303051519
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
bake part of oven would not heat, element fried in many areas
(e.g. First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...) I did have a problem with the wire connectors. they were a little over heated and loose, so I used pliers to ajust the connection.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Spokane, WA
- Parts Used:
- 5303051519
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Burned out oven bake element (bottom element).
***Make sure power is off the stove*** then remove oven racks.
Used 1/4 inch socket to remove 2 screws holding in the heating element, then pulled the element out a couple of inches to get at the wiring. Used pliers to unplug 2 spade clips.
Reversed procedure to install new element.
Used 1/4 inch socket to remove 2 screws holding in the heating element, then pulled the element out a couple of inches to get at the wiring. Used pliers to unplug 2 spade clips.
Reversed procedure to install new element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Sarasota, FL
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
The old element disintegrated into little pieces
Please make sure the oven is off before working on oven.
Removed element by removing the 1/4 inch bolts. There were spade lugs attached to it end of element inside hole around insulation. Be careful as to not let spade lugs slip back into hole. I left it attached to broken elemnt piece until I was ready to install new one. That way it held it into place.
Cleaned out the oven of all the fragments with a rag and warm bucket of water... Installed new element. Turned on oven to about 200 degrees F. for about a half hour to dry out and bake out any impurities
Removed element by removing the 1/4 inch bolts. There were spade lugs attached to it end of element inside hole around insulation. Be careful as to not let spade lugs slip back into hole. I left it attached to broken elemnt piece until I was ready to install new one. That way it held it into place.
Cleaned out the oven of all the fragments with a rag and warm bucket of water... Installed new element. Turned on oven to about 200 degrees F. for about a half hour to dry out and bake out any impurities
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- loren from dover, OH
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
heat element for oven burnt out
removed 2 screws removed clips on old heating element installed new element by placing clips on new part screwed element to back wall of oven total time about 5 min note this stove was 25 years old and part was still available sweet
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- stephen from york, PA
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burnt out
removed 2 screws , pull element forward , disconnected connector . pushed connectors on
the new element, pushed the ends back in place
and 2 screws and done . like 3mins.
the new element, pushed the ends back in place
and 2 screws and done . like 3mins.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barney from Naylor, MO
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set
lower heating element burned out
i removed the 2 screws that held the elrment in place. then pulled the element out about 3 inches and disconnected the two wires , reconenected the 2 wires to the new element and pushed it back in and replaced the 2 screws. the only part available locally was through a service man who would not sell it without installing it. at twice the price plus a service call.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sue from Lampasas, TX
- Parts Used:
- 5304409888
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Control will not work - only clock blinks
Took 3 panels off to get to the electric block. Replaced electrical block and put it back together. Still no change.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from Foley, AL
- Parts Used:
- 5304524341, 316538904
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken globe in oven and burnt out light bulb
Easy as 1-2-3
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- kathy from Eatonville, WA
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
change baking element
unscrew disconnect wires put new one on make sure you turn off power
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PAMELA from SAINT HELEN, MI
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Replacement of oven element
My husband had no problems except the end of the new element was different than the original, but hooked it up ok!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LINDA from WINN, MI
- Parts Used:
- 5308014251
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken burner on cooking stove.
lifted the top took out the old part that was broke, then put the new part in. (very simple)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KENNETH from SALMON, ID
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
No Heat
Remove defective element and replace with new heating element, bench checked servicable.
Was this instruction helpful to you?
Thank you for voting!