TEF317BWF Tappan Range - Instructions

Turn off power, remove heat coil assembly and drip pan. Unscrew the terminal assembly from the range top. Cut back 3 inches on each terminal wire and strip insulation 3/8 inch. Terminal assembly should be with the short side of the black block (from the side securement hubs) facing toward the coil stems. Slide the shrink wrap onto each wire and Twist each old with each new wire using the wire nuts and slide the shrink wrap Over each. Using a hair dryer, heat gun, or open flame carefully shrink the wrap. Secure the terminal back in place on the range.

Drank a beer, grabbed a screwdriver & tried to remove the two screws that held the element in place. The screws were old and when I turned them, they stripped instantly. This required another beer. Eventually I used pliers to grip the sides of the screws to remove and reinsrt them. When I finished the oven worked great, so I celebrated with another beer.

Pretty easy installation; you lift the top plate up and snip the wires maybe four inches away from the burner. Leave more wire than you think you need; once you get into it you'll realize you need more wire length than you think.

Then strip the remaining ends, twist them together with the provided caps, and use the heat shrink to hold it together. Remove the old terminal, replace it with the new ones, and you're good to go!

Remember to check that the wires are tight in the cap before heat shrinking, though. I had to get more shrink wrap in order to finish.

First, I read about the experiences of others who did this repair.

Then I removed the oven door by removing the single screw at each hinge - visible when the door is open - using a #2 Phillips screwdriver (the only tool needed for this repair). I placed the door on the kitchen table and removed the two screws at the inside top of the door - they also hold the handle onto the door.

I placed the four screws removed from the inside corners of the door -- into one corner of a tray I used to hold the parts in order. Then I removed the eight screws from the perimeter of the door and placed them into another corner of the holding tray. Then I turned the door over and removed the outside part of the door from the inside - as in removing the cover from a box.

Then I removed four screws holding the middle and outside glass panels and placed them in another corner of the parts tray. Then I removed two screws holding the steel panel against the glass. Then I removed the broken glass from the bottom of the tray. That's when I discovered I had ordered the wrong glass panel.

I called the PartSelect number to return the glass, and while discussing how to return the part, I asked if I had to call another number to get the correct part. The lady assured me she could process my order for the correct part. She was very knowledgable about the system and quickly found the correct part from the schematic. I received the replacement part 24 hours later and installed it within 20 minutes.

Overall a success story. Excellent service and easy work.

Remove drawer. Insert new slide. Install drawer.

All I had to do was loosen the screws, pull out electrical hookup on both ends, hookup new heating element to elecric and screw em into place. That's it, super easy and I got the part in 2 day : )

Sat on floor, pulled drawer out, inserted new clips, remounted door, stood up, high-fives myself.

The problem was caused by the owner placing an aluminum catch pan under the bake element. The failure of the element was where it was in contact with the pan. The repair involved removing two screws pulling out the element to access the wires. The connectors were the pull off type so I just disconnected the wires from the old element and placed them on the new element, pushed the element back in place and replaced the two retaining screws. I suggested that the owner not place anything in contact with the bake element. Be sure to up-plug the stove plug before attempting repair.

Once I recieved the new part it was easy to determine what two screws to remove to remove both the panel and the handle. I removed the two screws, slid the panel up and removed it. The new panel locked into place when slid down over the door and I replaced the sctews.

Take the screws out of the inside of oven for the element and slide the oven away from way and remove the back and insert the element to the clips and screw the back of the oven back together and plug in again and push back in place. Very easy for my husband to repair.

After doing without the oven for a week or so we decided to turn to the internet and try doing the repair ourselves. We are not mechanically inclined/fix it yourself kind of people. This really was easy. Just detach the old element and attached the new one. A couple of bolts and snapping one out and then the new one in. Very simple

Remove the 2 nuts holding the element in place. Pull the element out slightly to expose the wires. each side of the element has a wire. Slide the wires off. Replace new element. attach wires and pu the 2 screws back in the element holders.

Turned off range/oven breaker. Opened the oven door. Removed two 5/16 hex head screws. Pulled bake element forward and removed the two slip on electrical connections from old bake element and put them on the new one. Replaced the two screws, closed the oven door, and proceeded to overhaul the kitchen faucet.

I unplugged the stove from the power plug in the wall. There are two screws at the back of the oven to hold the element in place. I removed the two screws. There are wire clamp inserts that attach to the element. Once the element was loose from the back wall of the oven, I gently pulled out the wire clamps. Removed the element. I laid the new element in the bottom of the oven and gently pushed the wire clamps into the new element. Re-attached the screws and put the power back into the wall and I was done. Easy, easy, easy. As for the drip pans, I pulled the element from the plug just under the stove top, cleaned the element and replaced the old drip pans with the new. Slid the element back into the plug and I was done.

I looked for the proper part on this site. I was even able to find a video on how to install the part. It was great to see the step-by-step directions and tools needed. I ordered the part. It came quickly so that I was able to get my oven repaired before my kids came home for spring break. The only problem I had was the old screws were really stuck on. I used some WD-40 and they were still quite stuck. I learned that by gently going back and forth with the nut driver, rather than just trying to turn in the correct direction, that the screws came out quite easily. I felt so proud to be able to fix my own stove and save money in the process! Very satisfying for a single mom. Couldn't have done it without the video directions.