30-1149-23-08 Tappan Range - Instructions

Removed broiler pan drawer,removed two screws on element unplugged wires,installed new one. ,Tried oven, works like it did when new. It couldn't have been easier,plus I saved a bunch of money thank you partselect mike m.

removed broiler front by depressing the indents on the door slides, removed two screws holding igniter cut wires on old igniter and spliced new igniter to existing wires with supplied wire nuts then reinstalled new igniter and tested have been using oven ever since

took of bottom pan and pan above the gas flame off and the igniter off , cut the two wires. replaced the igniter hooked the wires togther, replaced both pans. turned the oven on and it lite

remove bottom pan, remove gas second cover, loosen nuts on ignitor, cut wires near the ignitor end for extra slack, connect new wire of ignitor, screw on wire caps, reattach ignitor, replace covers and finished. Very easy repair.

followed directions enclosed.required removal of oven door and old igniter

I looked up the model number of the Tappan oven on the net, found the part on the PartSelect site, ordered it and it arrived within a few days. The disassembly should have required nothing more than a Phillips head screw driver, unfortunately one of the screws was completely frozen and I managed to strip the Phillips head socket.

The screw was in a very awkward position so I first tried using grip pliers on the edge of the screw - this failed, I then tried grinding a flat spot on either side of the screw circumference and using the flats for gripping - it worked but the screw wouldn't move. Finally, I took a hacksaw blade and cut a slot in the head of the screw. I widened the slot using miniature files and finally made the slot wide enough for a large slot blade screwdriver - this worked. After removing that one screw and maneuvering the broken hinge out of the access hole on the stove front (the break in the hinge was such that this took awhile) the rest of the repair went very quickly.

The oven door was such that I could not see all of the hinge and when the part arrived from PartSelect I thought it was the wrong part. I called your parts return number to ask some questions. The lady who took my call was extremely helpful and we first discussed the part ID, then she showed me how to find a picture of the actual part on your site. After looking at the picture and the diagram I suddenly realized the part was correct - it was just that I thought it was supposed to be installed in a different manner. I'm sorry I didn't remember to get her name because she certainly should be commended for he patience and her assistance. Thanks Again.

I removed the oven floor and subfloor. I detached the old ignighter leaving the wires still attached. I then attached the new ignighter and fed each of the two new wires down through the bottom of the oven floor following the same path of the old wires which were still attached. I attached the new wires one at a time to make sure I connected them to the right place. Then, I pulled out the old igniter. I then attached the oven floors and turned the oven on which now works. The tough part is pulling the oven out from the wall to disconnect the power and turn off the gas. I did not remove the oven door.

1 - I unplugged the oven/ stove connection.
2 - Removed 2 screws and lifted it out the floor of the oven.
3 - Removed the nut holding down the flame guard and lifted it out.
4 - Removed 2 screes that held igniter in place.
5 - cut the wires for igniter.
6 - Stripped new wires with the nuts connector.
7 - Installed new igniter with 2 screws.
8 - Put it all back together step 3 & 2.
9 - Plugged in the oven/stove connection.
10 - Turn on the oven and works perfectly.
11 - My wife and daughter happy and ready to bake.

First unplugged the oven from the wall and then I removed the bottom floor of the oven by removing the two screws at the back. Then I removed the heat shield over the burner by remove the two screws at the front of the oven and removed the nut in the middle of the heat shield that was hold the shield to the burner. I removed the two screws on the flat oven igniter and cut the two wires on the igniter and pulled the two wires through the open in the bottom oven from the drawer opening. Mounted the new igniter and feed the two wire from the igniter through the open in the bottom of the oven, Stripped the two wires that I cut from the oven, twisted the new wires to the old, and put the wire nuts on. Last I put everything back together and baked dinner. Took ten about minutes and saved a thousand dollars because I was going to buy a new oven. Thanks, Partselect.

Unplugged the appl. I removed the bottom of the oven. Disconnected the two wires. Removed two screws that hold the element in place. Replaced it. And put everything back together. Since this element goes bad about every year an a half, I keep one on hand all the time.

I removed the bottom of the oven and flame guard for access to the ingniter. I then replaced the ingniter. The oven works like new now.

Removed the broiler compartment door by depressing the slide stops inward and pulling the door off. Turned off the breaker to the oven. Used a nut driver to remove the old ignitor ( 2 screws ). Cut the wires off the old ignitor close to the porclin. Measured the new ignitor wires to match up with the old ignitor wires and cut them. Stripped 3/8 " off ends of newely cut wires of the ignitor and used the supplied wire nuts to secure them together. Replaced the new ignitor with the 2 screws. Turned on the oven and a cooking I went.

I cut the wires from the old igniter near where it said to. I then connected the new wires to the old ones, put it back on, the way I remembered it being assembled, but still won't heat up. I tried to get an enlarged detail of where I was working on, but I couldn't enlarge it from your website. My friend, who knows about electricity, worked on it for several hours last pm(He's an electrician), but could not figure it out with the scamatic that was on the range, because he was not there when I disassembled it,

Unplugged stove, removed floor of oven, removed two screws holding igniter, cut wires to igniter, installed new igniter, cut and stripped wires on new igniter and leads, connected new ingiter with supplied ceramic wire nuts, tested (worked perfectly!), then replaced oven floor.

It was a snap!

I first removed the 2 screws that held the oven floor in place. Once removed, I remove the cover plate that covered the ignitor.

In order to get to the ignitor wires, I had to remove the drawer. Once the drawer was removed, I marked which wire went to which spot on the ignitor, then cut the wires. I then removed the old ignitor by removing 2 screws. I then attached the new ignitor with the 2 screws and attached the wires using the enclose wire nuts.

The complete process was very easy, taking less than half an hour. The part with shipping was just over $50. If I paid someone to fix my problem it would have cost at least $200. I'm sure galad I found this web site.