TGF336BHWD Tappan Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Patricia from Jacksonville, FL
- Parts Used:
- 5304506004
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The inside glass window panel had cracked.
It was extremely easy, I took the two screws out by the hinges and then slid the door up off the hinges. After that I removed all the outer screws, a total of 8, and took the panel off. I then had to remove maybe 6 to 8 more screws in order to get to where the inside glass panel was. I then replaced the glass and put the door back together. It was such an easy job, that if anything else breaks rather than assuming I need to replace it Im gonna look on here to see if it can be repaired.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- marc from troy, MI
- Parts Used:
- 5303935066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
oven took longer and longer to ignite ,then just stopped.
took out the cove plate inside oven. romoved old igniter load.cutt and stripped new wire to new ignighter , using ceramic wire nuts supplied. reinstalled all and voila. it's as good as new. PS just for safety sake always unplug appliance from power.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jackie from Palmdale, CA
- Parts Used:
- 5303935066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Oven would not come on, broiler worked and so did the burners
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...
And re-connected the same way.
Peice of cake..
Thank You..
And re-connected the same way.
Peice of cake..
Thank You..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Ogdensburg, NY
- Parts Used:
- 5303935066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Oven would not turn on , igniter burned out
1. Removed top over the oven burner.
2. cut the two wires conneted to the igniter about
an inch and a half.Noted which wire goes to the top of the igniter and which one went to the bottom.
3. unscrewed the igniter from the mount and
carefully pulled it from the oven.
4. put the new igniter wires through the hole.
5. mounted the igniter to the burner.
6. attached the new wires to the top and bottom old wires with the connectors that came with the igniter.
7. pluged the range back in and turned on the oven. Igniter works great.
2. cut the two wires conneted to the igniter about
an inch and a half.Noted which wire goes to the top of the igniter and which one went to the bottom.
3. unscrewed the igniter from the mount and
carefully pulled it from the oven.
4. put the new igniter wires through the hole.
5. mounted the igniter to the burner.
6. attached the new wires to the top and bottom old wires with the connectors that came with the igniter.
7. pluged the range back in and turned on the oven. Igniter works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Houston, TX
- Parts Used:
- 5303935066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Oven Would Not Light
Removed broiler pan drawer,removed two screws on element unplugged wires,installed new one. ,Tried oven, works like it did when new. It couldn't have been easier,plus I saved a bunch of money thank you partselect mike m.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jODY from GREAT FALLS, MT
- Parts Used:
- 5303935066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
ignitor wears out, tenants use the stoves as heat sorce
Opened the oven, removed the bottom plate located the ignitor within arms reach, removed two screws and a snap out part. replaced with the new ignitor and put the stove bottom on and waala...DONE
I have ordered all my parts from Parts Select and have never had a problem. Thank you. Jody in Montana
I have ordered all my parts from Parts Select and have never had a problem. Thank you. Jody in Montana
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Chicago, IL
- Parts Used:
- 5303935066
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
oven would work intermittently
remove bottom pan, remove gas second cover, loosen nuts on ignitor, cut wires near the ignitor end for extra slack, connect new wire of ignitor, screw on wire caps, reattach ignitor, replace covers and finished. Very easy repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- clayton from rockford, IL
- Parts Used:
- 5303935066
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
would not light
open oven door remove bottom of oven then remome the metal cover over the burner to expose the ignighter remove 2 screws that hold it to the bracket. the two wire's that come out of the ignighter run down under the bottom oven pan, i removed the bottom front cover by lifting up and then pulled out, then i could see the wires i removed the wire nuts and pulled old wires off and removed old ignighter. i pulled off the insulator covers from the old one and slid them on the wires of the new ignighter then i fished the wires back down and and attachted them with the wire nuts, then reasembled the rest of the oven. woks great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- lois from middletown, DE
- Parts Used:
- 5304506004
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
interior oven door glass cracked
All visible screws on sides & top of door, including screws for the door handle have to be removed. Fairly uncomplicated job, but as the glass that needed to be replaced, was 4th of 4 layers of glass, all needed to be removed from the outside in, in sequence, to get to the broken piece. Then as long as everything was apart, cleaned all pieces, before reassembling. Job much easier with two people, as one can hold & align all layers together, as the other tightens all the screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- stephen from LIVERPOOL, NY
- Parts Used:
- 5303935066
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
GAS OVEN WON'T LIGHT.
AS YOU DESCRIBED IN YOUR YOU-TUBE VIDEO, THE OVEN IGNITER WOULD GLOW BUT THE OVEN WOULD NOT LIGHT. YOU EXPLAINED THAT THE PROBLEM COULD STILL BE THE IGNITER AND SO I ORDERED A NEW IGNITER AND THEN WATCHED YOUR VIDEO ON HOW TO ACCESS AND REPLACE THE NEW IGNITER AND THAT FIXED THE PROBLEM. I ONLY HAD TO CUT THE OLD WIRES ON THE OLD IGNITER AND MATCH WIRES WITH THE NEW IGNITER USING THE CERAMIC WIRE NUTS SUPPLIED, AND I WAS BACK COOKING AGIN. THANKS.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Blanca from Union City, NJ
- Parts Used:
- 5304534377
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
replaced theoriginal power cord.
moved the stove forward and removed old cord by uncruing two small screw and on ploged the all and replaced with the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Pittsburgh, PA
- Parts Used:
- 5303935066
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Oven would not light
After diagnosing the problem, I entered the Tappan Model #, found the part needed, and ordered from Part Select. On receipt (2 day delivery), I followed the instructions enclosed with the ignitor, and within 30 minutes, had everything up and running. Thanks PART SELECT!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jody from Storrs Manfield, CT
- Parts Used:
- 5303935066
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Oven would not heat.
Turned the gas and the electricity off to the gas range. Took the two large screws out in the back of the range holding on the first pan. Have to look for them. Took off the single nut holding on the second pan. Used nut drive #10 to take off nuts. Be careful you do not lose them. Took off inoperative unit. Cut wires to unit. Stripped wires which connect to range. Put new unit on and tightened nuts with nutdriver. Spliced wires together and put on wire nuts securely. Taped them to the wires. Put the second pan back, then the first pan. Turned on gas and electricity to test.
Worked fine. Found that the old unit was cracked and had a piece missing. Must use flashlight. Be safe.
Worked fine. Found that the old unit was cracked and had a piece missing. Must use flashlight. Be safe.
Was this instruction helpful to you?
Thank you for voting!
The tubes which fed gas to the burners were broken due to raising and lifting the top cover which caused gas to leak under the top cover.
I had no experience working on the stove before so it was all new to me. Removed the top cover. Removed the igniters and the burner connections which allowed access to the splash pan. Removed the splash pan and replaced the two broken tubes. Job would have been faster had I known how to access the front burner controls. As a result, we have a fully functioning Tappan range in our kitchen and the range is much better than anything commercially available. They don't make em like that anymore.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BETTY from PHILADELPHIA, PA
- Parts Used:
- 5303935066
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
igniter burned-out, not able to start oven
followed directions enclosed.required removal of oven door and old igniter
Was this instruction helpful to you?
Thank you for voting!