32-1039-00-05 Tappan Range - Instructions

Replaced the flat style oven igniter. Turn off gas and unplug oven. Removed the broiler drawer, cut wires, unscrewed oven igniter (using a small/medium adjustable wrench), connected wires, fastened new igniter to bracket, spliced wire, twisted together, plugged oven back in, turned gas on, turned on oven after a few minutes...worked great.

took out the old (2 screws) put clip on wires and put the new part in. Simple

I first removed the 2 screws that held the oven floor in place. Once removed, I remove the cover plate that covered the ignitor.

In order to get to the ignitor wires, I had to remove the drawer. Once the drawer was removed, I marked which wire went to which spot on the ignitor, then cut the wires. I then removed the old ignitor by removing 2 screws. I then attached the new ignitor with the 2 screws and attached the wires using the enclose wire nuts.

The complete process was very easy, taking less than half an hour. The part with shipping was just over $50. If I paid someone to fix my problem it would have cost at least $200. I'm sure galad I found this web site.

Remove the oven drip pan & burner baffle. unscrew & cut leads to remove old igniter. Splice old leads to new using furnished wire nuts and remount. Job would have been easier with oven door removed, but didnt want to create a new project.

took drawer out, removed tin covers, found igniter and removed,snipped off parts to put on new igniter ,wirenutted old to new put back together ,we had ignition! all in all pretty easy job! detailed instructions that came with new part were easy to follow and precice

Checked voltage supply to oven igniter, had 120 v
to oven igniter, but igniter was not glowing.

I exposed the ignitor through the inside of the oven and then removed the two screws that held it in place. I then cut the wires underneath the stove ans reconnected them to the new part with the wire nuts provided. It was a simple repair.

Unplug appliance. Remove the bottom of the oven (2 screws in back of oven bottom), remove burner cover (2 screws in front and nut in center holding burner). Pull out the bottom storage drawer under the oven and unplug both wires from oven Igniter which are located in the back. One wire plugs into the gas valve and the second wire went into a connector that was on the lower left. I removed the screw on the back oven wall that held the burner so I could remove the burner for ease of work. Remove two screws holding the old igniter. The two screws holding the igniter to the side of the burner were stripped and they took a little time to remove but I replaced them with two new screws I had in my misc. screw drawer and had no issue. Cut the top wire and splice it onto the top wire of the new igniter using the porcelain wire nuts provided. Do the same with the bottom wire. Re-assemble and plug back in. Everything worked perfectly.

1. Unplugged power cord.
2. Removed warming drawer and oven shelves and lower plate
3. Removed old wirenuts from back of warming draw space (awkward to reach in to the back).
4. Removed 2 screws holding ignitor in oven - screws in poor shape and were not reuseable.
5. Found next size up sheetmetal screws and installed new ignitor.
6. Ran wires down adjacent to gas feed into warming drawer space.
7. Connected with wirenuts supplied with ignitor.
8. Replaced everything.
9. Tested oven and ate some tasty blueberry muffins.

My husband was able to easily remove the old part, and replace with the new ignitor. The wires were long, so he took the extra precaution of tying them away from the flame. It took longer to take everything out and put it back together than the actual repair..

First, I read all the instrutions that came with my replacement part from Parts Select thoroughly (twice) then follewed them like an experienced surgeon. I removed the lower drawr after turning off the gas and unplugging the stove and then took out the bottom panels inside the oven to expose the screws holding the ignitor coil. Removed it, then cnnected the new one to the existing wires as they were in the stove and the drawing in the instructions, then replaced everything in the reverse of them coming apart. Plugged it back in, turned the gas back on and now it,ll bake things again. YEAH!! Parts Select!!!

Removed the two screws, took out the old one and replaced the new one. It was very easy and the oven works great now. Thanks.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I made sure I memorized just how the wires would re-connect with the wirenuts. I then re-assembled everything. Be sure to read all the instructions, especially how to properly install wirenuts. I was able to access the wire connections below the oven chamber through the drawer at the bottom of the range. This is an important detail.

removed the old igniter, installed the new one. 15 minutes, piece o cake!

took the old igniter out and swapped the connectors onto the new one. Kept the connectors close to the connector end to prevent them from being to close to the ovens heat.