31-2649-23-10 Tappan Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- ROBERT from MAINEVILLE, OH
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Heating element went out
Simply...2 hex head screws removed. Unplug old element...plug in new element...place 2 screws back into place...test
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- rosetta from COLUMBIA, VA
- Parts Used:
- 3051162
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
problem pulling out bottom tray on range
just put in slot
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- david from PERRY, ME
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bad element
Remove screws pull off wires and install new parts
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Amber from CARLISLE, PA
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake element (bottom of oven) burnt through and snapped in two
Unplug the oven, remove oven racks, unscrew 2 screws at the base of oven bake element, pull the terminals off the wire bases, plug terminals back in, put screws back in place, plug in oven and test that it works...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vincent from Bonita Springs, FL
- Parts Used:
- 318036310
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Knobs for the three timers on the appliance console deteriorateddue to age.
The repair was very simple and easy. All I hqad to do was remove the old knobs and attach the new ones. No tool was required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arlene from ERIE, IL
- Parts Used:
- 316442300
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Burner not heating up.
Unpluged old one pluged new one in. So good to have a burner that all the coils heat up.
Was this instruction helpful to you?
Thank you for voting!
Broken right side parts for lower over storage drawer.
Sat on floor, pulled drawer out, inserted new clips, remounted door, stood up, high-fives myself.
Was this instruction helpful to you?
Thank you for voting!
My burners were shot!
Pulled out the old, and replaced. Very simple for a 62 year old woman! I cook a lot, being from the country, and Imwas so excited to get my burners fixed! Should have done it years ago! Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jim from gorman, TX
- Parts Used:
- 316442300
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
high power awful smell
raise top of stove unplug burner plug in new one done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Earl from Elkin, NC
- Parts Used:
- 316075103
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Bake element wouldn't heat.
The problem was caused by the owner placing an aluminum catch pan under the bake element. The failure of the element was where it was in contact with the pan. The repair involved removing two screws pulling out the element to access the wires. The connectors were the pull off type so I just disconnected the wires from the old element and placed them on the new element, pushed the element back in place and replaced the two retaining screws. I suggested that the owner not place anything in contact with the bake element. Be sure to up-plug the stove plug before attempting repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Debbie from Mineral Wells, TX
- Parts Used:
- 316075103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Bake Element burned in to stopped working
Turned off power to appliance removed the screws connecting the element. Disconnected the wires from the old element connected the new element replaced the screws and tightened turned power on turned power back on heated oven to be sure it worked. Very simple to do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevi from Verona, WI
- Parts Used:
- 316075103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
heating element stopped working
All I had to do was loosen the screws, pull out electrical hookup on both ends, hookup new heating element to elecric and screw em into place. That's it, super easy and I got the part in 2 day : )
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Hopkinsville, KY
- Parts Used:
- 316075103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
oven Bake Element burned up and broke
this bake element has two special Hex style screws, securing it in place, but a nut driver worked just as well. remove the baking racks, and then loosen the two hex screws. slowly pull the element out of the back wall and then disconnect the electric leads. reinstall by doing then the opposite action. could not have be simpler.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from Gregory, MI
- Parts Used:
- 3051163
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The right Drawer Glide was broken.
The simplest repair ever! I just snapped it in and put the drawer back - fixed. I hope I have other repairs this simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from Iowa City, IA
- Parts Used:
- 316075103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench set
Element did not heat
After doing without the oven for a week or so we decided to turn to the internet and try doing the repair ourselves. We are not mechanically inclined/fix it yourself kind of people. This really was easy. Just detach the old element and attached the new one. A couple of bolts and snapping one out and then the new one in. Very simple
Was this instruction helpful to you?
Thank you for voting!