33-1027-23-01 Tappan Range - Instructions

Removed the 2 element holding screws, disconnected the element leads & remover element. Replaced with new element.
All in all a real easy job (wish all repairs went this easy)
PartSelect had the element at the house within a couple days (Correct part I might add) which made the wife happy !!

Unscrewed back of oven the plate that was holding on old element, removed it (plugged into small wire device)
Plugged in new one and replaced screws to hold in place.

replaced it

Watching the video showed an easy, unscrew and screw back on process while connecting the wires back. It was really that simple. Once it was complete (not even 10mins), plugged it back in, and its been working great since.

1. First I pulled out the heating element from stovetop and removed old pan (no screws) very simple. 2. Put new pan in and inserted the heating element back in place.

First I removed the 2 screws on each side of the element and then pulled the element out, disconnected the 2 wires that were holding the element, got the new element and connected it to the wires, slid back into position, put the screws back in that hold the element and put the racks back in and turned on for test. It was so easy I had it done before my husband arrived home from work.

Took the back panel off. Removed the 2 screws from the old element,removed it. Put the new one in and replaced the screws. Put the back panel on done. What took the longest was cleaning behind there !!

The meltdown was a spectacular event. After clearing the kitchen of smoke and allowing the oven to cool down. I easily removed the remnents of the old element by removing the screws holding each side in place and disconnected the two wires. I then insulated the hot side wire (red) to prevent the possibility of a short when resetting the breaker in order to use the stove top. The next day I found PartSelect.com and ordered the very reasonably priced new part with optional overnight shipping. it arrived at 1:00 pm the following day. Installation was a simple reverse of the removal. The oven works great and I now keep a fire extinguisher in my kitchen.

Moved stove out from wall and cabinets, then unplugged the stove. Removed the oven racks, then removed the 2 screws securing the baking (lower) element to the rear wall of the oven. Pulled the element out a few inches and disconnected it from the stove wires. Removed old element. Removed screws from rear panel to gain access to wiring. Inserted new element and connected to wiring. Put element in place and replaced the 2 screws in rear wall. Put rear panel back in place and replaced panel screws. Plugged stove back in and moved back into place. Tested oven and it worked just fine. Parts Select did a great job of filling my order and promptly shipping it. I got it in 2 working days.

I had a friend come..He unpluged the old one and put the new one in when it arrived. All is well. Thank you for having the part that was needed. Now the over works super..
S.Bullock

took off the back of the stove..first Unplugged it! and undid the old unit, and put the new one on....easy peasy!..Thanks for your fast mailing!

Turned off main power at electrical breaker. With pliers, removed two screws that hold element in place. Pulled element out about 3 to 4 inches. Disconnected two wires from element. With pliers, adjusted connections on new element connections from horizontal to vertical position. Connected two wires to connections of new element. Installed new element in oven with original two screws. Powered on main electrical breaker. Oven back in operation! Also, part arrived in 3 days! I'm a happy camper!

I used this site self diagnostic page and ordered the oven heating element as that was the item suggested for repairs. It was the correct part to fix my oven problem. I had my electrician visiting to install two light fixtures so I had him install the new heating element in the oven. Even with him going to the garage to turn the circuit breaker off for the range the installation took less than 5 minutes.
This site is the greatest!

I unhooked element from wall on inside. Only two screws to undo. I then took back of stove off and unhook speaker like connectors. It was very simple.

Had to drill 2 new holes 1/4 lower in oven so new coil would bolt up evenly besides that it went easily.