TGF357BCWB Tappan Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Gary from Darragh, PA
- Parts Used:
- 316067902
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed an additional rack
Open the door and slide in the new rack.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from WEST UNION, OH
- Parts Used:
- 3051162
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
One guide was missing and the other was broken
Read the instructions provided and simply installed the guides. Total time was less than 5 min.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- david from SLIDELL, LA
- Parts Used:
- 5303935066
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
OVEN WOULD NOT COME ON
CUT THE WIRES ON OLD IGNITER AND WIRE NUT THE WIRES OF THE NEW IGNITER TO WHERE I CUT THE OLD ONE OFF.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Huston, TX
- Parts Used:
- 5303935066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
would not light oven
take off the old by unsceawing it scraw thenew one onput the wires down the back throw the hole put the wires to gather and cap tham plug the elect. back in and turn it on for to test it wow it worked he he ...richard
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jackie from Palmdale, CA
- Parts Used:
- 5303935066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Oven would not come on, broiler worked and so did the burners
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...
And re-connected the same way.
Peice of cake..
Thank You..
And re-connected the same way.
Peice of cake..
Thank You..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- charles from bossier city, LA
- Parts Used:
- 5303935066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
oven would not allow gas to flow for igniter to light
removed broiler front by depressing the indents on the door slides, removed two screws holding igniter cut wires on old igniter and spliced new igniter to existing wires with supplied wire nuts then reinstalled new igniter and tested have been using oven ever since
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- larry from 775, TX
- Parts Used:
- 5303935066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
oven would not light
pulled drawer out and took old igniter off and replaced it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Akron, NY
- Parts Used:
- 5303935066
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
oven wouldn't light uneven temp.
had to remove burner bolts holding igniter were stripped cut two wires replaced igniter using two self tapping screws put wires together using wirenuts Honey making cookies right now thanks already told friends about you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jody from Storrs Manfield, CT
- Parts Used:
- 5303935066
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Oven would not heat.
Turned the gas and the electricity off to the gas range. Took the two large screws out in the back of the range holding on the first pan. Have to look for them. Took off the single nut holding on the second pan. Used nut drive #10 to take off nuts. Be careful you do not lose them. Took off inoperative unit. Cut wires to unit. Stripped wires which connect to range. Put new unit on and tightened nuts with nutdriver. Spliced wires together and put on wire nuts securely. Taped them to the wires. Put the second pan back, then the first pan. Turned on gas and electricity to test.
Worked fine. Found that the old unit was cracked and had a piece missing. Must use flashlight. Be safe.
Worked fine. Found that the old unit was cracked and had a piece missing. Must use flashlight. Be safe.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- david from granville summit, PA
- Parts Used:
- 5303935066
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench set
my oven wouldn't light
first i removed the bottom of the oven [inside the oven] ,the part was right there,i removed 2 screws and unpluged the wires,then i cut the wire ends off the old part and used the wirenuts that came with the new one to hook them to the new part,then put it back in place,put the screws back in put the bottom back in and was done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Pittsburgh, PA
- Parts Used:
- 5303935066
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Oven would not light
After diagnosing the problem, I entered the Tappan Model #, found the part needed, and ordered from Part Select. On receipt (2 day delivery), I followed the instructions enclosed with the ignitor, and within 30 minutes, had everything up and running. Thanks PART SELECT!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carroll from Jackson, MI
- Parts Used:
- 5303935066
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
occasional failure to light-wife didn't trust it.
Removed oven door. (two screws)
Removed racks.
Removed oven floor. (two finger screws)
Removed diverter (V) tray. (one nut)
Removed small panel @ left lower back of oven
(1 screw) to access elect. power disconnect.
Disconnected power.
Removed element (two square drive screws)
Snipped and stripped old wires, connected new
with ceramic wire nuts supplied.
Installed new element, reversed proceedure.
Oven lights in 10 seconds. Wife happy!
Probably 40 minutes, could do it again in15-20
once you know what tools to lay out.
Removed racks.
Removed oven floor. (two finger screws)
Removed diverter (V) tray. (one nut)
Removed small panel @ left lower back of oven
(1 screw) to access elect. power disconnect.
Disconnected power.
Removed element (two square drive screws)
Snipped and stripped old wires, connected new
with ceramic wire nuts supplied.
Installed new element, reversed proceedure.
Oven lights in 10 seconds. Wife happy!
Probably 40 minutes, could do it again in15-20
once you know what tools to lay out.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JERRY L from PIPER CITY, IL
- Parts Used:
- 5303935066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Oven wouldn't light
Removed oven door, removed oven floor. Unscrewed skirt with attached igniter and gas tube. Two nut screws hold igniter to burner. Remove old igniter and replace with new, reattach two wires with supplied wire nuts. Replace oven floor and door. Oven lit right up, pizza anyone?
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Chicago, IL
- Parts Used:
- 5303935066
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
oven would work intermittently
remove bottom pan, remove gas second cover, loosen nuts on ignitor, cut wires near the ignitor end for extra slack, connect new wire of ignitor, screw on wire caps, reattach ignitor, replace covers and finished. Very easy repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marvin from MONTANA CITY, MT
- Parts Used:
- 3051162
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
guide was broken
Used a slot screwdriver to pry the old guide...clipped the new guide into its place.
Was this instruction helpful to you?
Thank you for voting!