30-2042 (13) Tappan Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Gary from REDFORD, MI
- Parts Used:
- 5303131115
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Replace Drip Pans
No Problem, couldn't find them at any local repair facility so I looked on line and found them here, ordered 4 drip pans and the exact replacements came within a few days.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from SPENCERPORT, NY
- Parts Used:
- 316035200
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Bad igniter in switch
Removed 4 burner knobs. Unscrewed 6 phillips head screws on manifold.Pulled back manifold enough to remove switch. Removed the Two wires from switch and hooked them up to the new switch. Slid new switch on to shaft and in reverse order, reasembled manifold, screws and knobs.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- david from canastota, NY
- Parts Used:
- 5303935066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
oven would not lite
took of bottom pan and pan above the gas flame off and the igniter off , cut the two wires. replaced the igniter hooked the wires togther, replaced both pans. turned the oven on and it lite
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from BUFFALO, NY
- Parts Used:
- 5303207048
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Wrong Part
I received the order in today's mail. However, the knob does not fit the thermostat port. I was excited the the knob you sent me looks exactly like my knob, However, The knob you sent me has a 1 at the port site. The knob on my stove has a 2 - it has a larger port opening.
Can this be remedied at all? Do you have a similar part with a 2 on the port hole?
Let me know if there is anything that can be done, Thank You.
Bob Alley
(716)875-1034 Landline
(716)367-8074 Cell
email: [email protected]
Can this be remedied at all? Do you have a similar part with a 2 on the port hole?
Let me know if there is anything that can be done, Thank You.
Bob Alley
(716)875-1034 Landline
(716)367-8074 Cell
email: [email protected]
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from GLEN MILLS, PA
- Parts Used:
- 5303204154
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Rusted out front burner
remove screw, remove burner, install new burner and screw
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from MANASSAS, VA
- Parts Used:
- 5303935066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Oven glows but won't ignite
Thank you, Thank you and thank you!!! I couldn't be happier and I save over $200 in repair. My repair was very easy after watching the video. I cut off the wire and ensure that the new one are attached into place. Placed all parts back and boom, the oven starts working a new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Houston, TX
- Parts Used:
- 5303935066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Oven Would Not Light
Removed broiler pan drawer,removed two screws on element unplugged wires,installed new one. ,Tried oven, works like it did when new. It couldn't have been easier,plus I saved a bunch of money thank you partselect mike m.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Chicago, IL
- Parts Used:
- 5303935066
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
oven would work intermittently
remove bottom pan, remove gas second cover, loosen nuts on ignitor, cut wires near the ignitor end for extra slack, connect new wire of ignitor, screw on wire caps, reattach ignitor, replace covers and finished. Very easy repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- larry from 775, TX
- Parts Used:
- 5303935066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
oven would not light
pulled drawer out and took old igniter off and replaced it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JERRY L from PIPER CITY, IL
- Parts Used:
- 5303935066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Oven wouldn't light
Removed oven door, removed oven floor. Unscrewed skirt with attached igniter and gas tube. Two nut screws hold igniter to burner. Remove old igniter and replace with new, reattach two wires with supplied wire nuts. Replace oven floor and door. Oven lit right up, pizza anyone?
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- clayton from rockford, IL
- Parts Used:
- 5303935066
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
would not light
open oven door remove bottom of oven then remome the metal cover over the burner to expose the ignighter remove 2 screws that hold it to the bracket. the two wire's that come out of the ignighter run down under the bottom oven pan, i removed the bottom front cover by lifting up and then pulled out, then i could see the wires i removed the wire nuts and pulled old wires off and removed old ignighter. i pulled off the insulator covers from the old one and slid them on the wires of the new ignighter then i fished the wires back down and and attachted them with the wire nuts, then reasembled the rest of the oven. woks great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- david from SLIDELL, LA
- Parts Used:
- 5303935066
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
OVEN WOULD NOT COME ON
CUT THE WIRES ON OLD IGNITER AND WIRE NUT THE WIRES OF THE NEW IGNITER TO WHERE I CUT THE OLD ONE OFF.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BETTY from PHILADELPHIA, PA
- Parts Used:
- 5303935066
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
igniter burned-out, not able to start oven
followed directions enclosed.required removal of oven door and old igniter
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Waco, TX
- Parts Used:
- 5303935066
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
replaced oven igniter
Removed racks,oven bottom(2 screws) and heat deflecter. Slide heat sleeves 10 inches away from old igniter. Cut wires one inch longer than the length of the heat sleeves, from the old igniter. Cut the new wires to match old wire length. Replace old igniter. Slide sleeves up to new igniter. Wire nut ends-done deal. It was hard working over the oven door,but I am old. Good luck
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Walter from Danville, IL
- Parts Used:
- 5303935066
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
oven would not lite
First i removed the broiler door and then I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and cut the two wires. I strip the ends ,connected the new unit with ceramic nuts that was provided an reconnected the unit. all was done in less than 30 min. EASY!!! plug the stove back in and WORKED PERFECTLY. note i receive the unit the same day it shipped....WOW
Was this instruction helpful to you?
Thank you for voting!