72-4252-23 (05) Tappan Range - Instructions

followed online instructions

I simply searched YouTube for the problem I was having and foud it was probably caused by a bad part. I found the part online and ordered it. It was as simple as a few screws and a couple wire-nuts to install. My girlfrind was very happy to get the oven fixed !!!!
Thanks parts-select for having pictures and dimensions so I was sure I had ordered the exact right part.
I was soooo happy to have found you !

pulled stove out to unplug the electric cord. Took oven door off and removed the bottom panel (2 screws) and then removed the burner (2 screws). took off old igniter ( 2 nut screws). cut wires and stripped the coating to wire to new unit.
Attached new igniter to the burner, and put the burner back in place and replaced the screws so unit was stable.
Turned oven on to make sure ingiter was going to light oven, when oven came on, turned oven off and replaced the cover to the burner and the bottom panel in the oven,. Put the oven door back on........
Probably took 45 minutes.
I ordered the part late Friday afternoon, around 3, and the part was here Saturday Afternoon. I was impressed.

Let me begin to say your service was great. I received the unit the next day. Also your price was good.
The whole job took me an hour. I would have done it sooner but I didnt a square head driver bit to remove the igniter from the burner assembly. I removed the whole assembly and with a pliers slowly unscrewed the mounting screws. After that I disconnected the igniter per your instructions,spliced the remaining wires reconnected the gas and electric and I was good to go.

I removed the oven bottom which was held by two large head long screws. I then removed the heat deflector using a small socket. The only difficult part was when I went to replace the igniter. The screws that were holding it in place stripped I guess do to the amount of heat they were continually subject too. I had to apply pressure to the igniter bracket while removing the screw using a small socket. Even with that they did not come out easily. If I had not had trouble removing the screws the repair probably would have taken 15 min.

My husband was able to easily remove the old part, and replace with the new ignitor. The wires were long, so he took the extra precaution of tying them away from the flame. It took longer to take everything out and put it back together than the actual repair..

could not determine what part failed.Found Part Select on line useing Bing search.Using virtual repairman and typing in the problem it told me what I needed.Orderd that part on line and reieved it in TWO DAYS,can you believe that! Inatalled that igniter in 15 mins. and now it works like new. Thank You Part Select!!!!!!

took out the old (2 screws) put clip on wires and put the new part in. Simple

From the front I cut the wires going to the old igniter and removed it. Then I stripped insulation back 3/8 of an inch. Using the ceramic wire nuts that came with the new igniter, I connected the new wires to the existing. Then I installed the new igniter and the job was done. I turned on the thermostat and the oven ignited quicker than it had for some time.

After finding your page and using your trouble shooting guide, it was easy getting the right part and the video helped a lot. Removed the over rack- removed two screws to remove the bottom- two screws to remove the burner. Clipped the two wires to the old igniter and removed the burner from the oven,removed the two screws holding the igniter and installed new one. clipped the wires to length and renistalled the burner. Using the two wire nuts supplied put the wires togather and reinstalled the bottom. Everything went well lite first try with no poof sound. Just in time for Thanksgiving cooking. Got fast delivery of parts. Will uas again. Thanks Partselect.

cut wires and removed the burner . Removed the ignighter and installed the new with nut driver. slipped the burner back in place and nutted the wires...Wallagh!!! fired right up...

Unplug electicity, Take out all inside pans, unscrew the burner arm, disconnect white power wires to the igniter. remover gas buner, detach the igniter and attach the new igniter to the burner arm. re assemble the burner arm, connenct the white wires to the white wires from the oven just below the igniter. Put all pans and guards back in oven, plug in and test.

Unplug electric , remove old igniter, cut wires, shorten new igniter wires, strip insulation, wire nut together, attach new igniter, plug in electric, fire it up. Worked great.

After removing heat shield, removed heating element (make sure you have the right bit, I stripped one of the screws). Cut wires , making sure to mark them. Reconnected and it worked like new! Saved a bunch of money,thank you!

removed bottom plate in oven removed three screws and cut two wires.