30-2272-23-01 Tappan Range - Instructions

first i removed the bottom of the oven [inside the oven] ,the part was right there,i removed 2 screws and unpluged the wires,then i cut the wire ends off the old part and used the wirenuts that came with the new one to hook them to the new part,then put it back in place,put the screws back in put the bottom back in and was done

I removed the oven floor and subfloor. I detached the old ignighter leaving the wires still attached. I then attached the new ignighter and fed each of the two new wires down through the bottom of the oven floor following the same path of the old wires which were still attached. I attached the new wires one at a time to make sure I connected them to the right place. Then, I pulled out the old igniter. I then attached the oven floors and turned the oven on which now works. The tough part is pulling the oven out from the wall to disconnect the power and turn off the gas. I did not remove the oven door.

Unplugged the appl. I removed the bottom of the oven. Disconnected the two wires. Removed two screws that hold the element in place. Replaced it. And put everything back together. Since this element goes bad about every year an a half, I keep one on hand all the time.

Removed the broiler compartment door by depressing the slide stops inward and pulling the door off. Turned off the breaker to the oven. Used a nut driver to remove the old ignitor ( 2 screws ). Cut the wires off the old ignitor close to the porclin. Measured the new ignitor wires to match up with the old ignitor wires and cut them. Stripped 3/8 " off ends of newely cut wires of the ignitor and used the supplied wire nuts to secure them together. Replaced the new ignitor with the 2 screws. Turned on the oven and a cooking I went.

pulled off old knob and put on new one. This knob fits a Tappan S110 gas range

Snapped it on!

First unplugged the oven from the wall and then I removed the bottom floor of the oven by removing the two screws at the back. Then I removed the heat shield over the burner by remove the two screws at the front of the oven and removed the nut in the middle of the heat shield that was hold the shield to the burner. I removed the two screws on the flat oven igniter and cut the two wires on the igniter and pulled the two wires through the open in the bottom oven from the drawer opening. Mounted the new igniter and feed the two wire from the igniter through the open in the bottom of the oven, Stripped the two wires that I cut from the oven, twisted the new wires to the old, and put the wire nuts on. Last I put everything back together and baked dinner. Took ten about minutes and saved a thousand dollars because I was going to buy a new oven. Thanks, Partselect.

1 - I unplugged the oven/ stove connection.
2 - Removed 2 screws and lifted it out the floor of the oven.
3 - Removed the nut holding down the flame guard and lifted it out.
4 - Removed 2 screes that held igniter in place.
5 - cut the wires for igniter.
6 - Stripped new wires with the nuts connector.
7 - Installed new igniter with 2 screws.
8 - Put it all back together step 3 & 2.
9 - Plugged in the oven/stove connection.
10 - Turn on the oven and works perfectly.
11 - My wife and daughter happy and ready to bake.

I removed the bottom of the oven and flame guard for access to the ingniter. I then replaced the ingniter. The oven works like new now.

replaced it

I cut the wires from the old igniter near where it said to. I then connected the new wires to the old ones, put it back on, the way I remembered it being assembled, but still won't heat up. I tried to get an enlarged detail of where I was working on, but I couldn't enlarge it from your website. My friend, who knows about electricity, worked on it for several hours last pm(He's an electrician), but could not figure it out with the scamatic that was on the range, because he was not there when I disassembled it,

The philip head screws holding the igniters were frozen. Had to cut off heads with dremel cut off tool, then grabed residual screw with vice gripp pliers. Removed screws and mounted new ignighters. Used new hex head bolts. Attached wires per instruction sheet and tested unit. It worked.

I simply searched YouTube for the problem I was having and foud it was probably caused by a bad part. I found the part online and ordered it. It was as simple as a few screws and a couple wire-nuts to install. My girlfrind was very happy to get the oven fixed !!!!
Thanks parts-select for having pictures and dimensions so I was sure I had ordered the exact right part.
I was soooo happy to have found you !

I removed the oven bottom which was held by two large head long screws. I then removed the heat deflector using a small socket. The only difficult part was when I went to replace the igniter. The screws that were holding it in place stripped I guess do to the amount of heat they were continually subject too. I had to apply pressure to the igniter bracket while removing the screw using a small socket. Even with that they did not come out easily. If I had not had trouble removing the screws the repair probably would have taken 15 min.

Removed lower burner covers and fan cover to access igniter. Unscrewed igniter and pulled out as far as possible. Marked both wires and snipped them. Twisted on wires from new igniter and mounted igniter. Pulled excess wire thru to back of oven and reassembled covers from first step. Last step was to explain to wife that she needs clean in there MUCH better.