F5007*1 Roper Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Raul from Oak Hill, FL
- Parts Used:
- WP660533
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burner made popping sound and began shooting sparks from one of the rings
extremely easy to replace the burner. I just pulled out the old burner and replaced with new one. The whole process took less than ten minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from reading, MA
- Parts Used:
- 330031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
contacts had gotten burnt out/blackened with age so burner was intermittent.
lifted the cover, unscrewed the ceramic wire fastners, put the new part in, and voila, job done and working perfectly
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janet from Uniontown, PA
- Parts Used:
- WP660533
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burner element was not working right
Since it was a plug-in burner, only needed to pull it out and put the other one in.
Another thing I would like to say is that I was very well pleased with the service from partselect.com. I was unable to find the burners in my area.
Was very helpful in selecting the part and was very efficient in sending it.
Another thing I would like to say is that I was very well pleased with the service from partselect.com. I was unable to find the burners in my area.
Was very helpful in selecting the part and was very efficient in sending it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from Lakewood, OH
- Parts Used:
- WP660533
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Would no longer heat up
Removed the old broken burner and slid the burner prongs into place. Very EASY to replace!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Brookings, OR
- Parts Used:
- 330031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Worn out terminal block
Turned off the power to the stove. Removed the 'burners' and 'burner' trays. Removed the screw that secured the bad block. Lifted the top of the stove. Cut the two wires to the bad block., stripped the wires about 1/2", slipped the shrink tube over the wires. Connected the new block with two porcelan wire nuts. slipped the shrink tube over the wirenuts and heated it with a lighter. Closed the top and secured the terminal block clip with a screw. Turned the power back on: voila!
All the necessary parts came in the repair kit, delivery was timely. Very easy project.
All the necessary parts came in the repair kit, delivery was timely. Very easy project.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- william from port st lucie, FL
- Parts Used:
- 330031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
contacts in plug-in block badly burned & oxidized
First I removed the one screw that held the element in place. I then pulled the element out about 3 inches and cut the two wires...)
Assembled the block parts.
Installed shrink sleve and applied wire nuts to electrical connection to 2 wires then shrunk the sleve.
Did the above procedure for 2 heating elements.
They work very well now.
Assembled the block parts.
Installed shrink sleve and applied wire nuts to electrical connection to 2 wires then shrunk the sleve.
Did the above procedure for 2 heating elements.
They work very well now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry from Grand Forks, ND
- Parts Used:
- 330031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
burner connector - bad connection
Removed burner and tray. Removed burner connector from stove top using screw driver.
Removed existing heat shrink and wirenuts.
Installed new connector - wire nuts and heat shrink. Used lighter to shrink.
Took 20 minutes.
Removed existing heat shrink and wirenuts.
Installed new connector - wire nuts and heat shrink. Used lighter to shrink.
Took 20 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roy from Moore, OK
- Parts Used:
- 330031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
range top burners not heating reliably
Removed the original burner element sockets and replaced with parts provided in kit. Instructions were simple and easy to follow, problem completely solved in 20 mins!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Crimora, VA
- Parts Used:
- WP8203546
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Block broke
Unplug power cord, remove wires from block. take 2 screws out. replace with new block about 15 mins. Done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sherrill from Houston, TX
- Parts Used:
- WP660533
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Hole in Cooktop Burner
Simply removed new burner from box and plugged it in! Very pleased with 3 day speedy delivery. Confident my 32 year old cooktop will continue to give many more years of service with any parts needed from PartSelect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pastor Shelly from Sumter, SC
- Parts Used:
- WP660533
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burner stop heating
pulled out old burner and pushed in new burner.
No tools needed.
No tools needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Shelby Township, MI
- Parts Used:
- 330031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Wire broken going to one electric plug for burner
Replace the connector and bracket, spliced the wires, put heat to the schrink wrap and I was done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from ST. Charles, MO
- Parts Used:
- 330031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
no heat from burner
I raised the stove top, read the instructions to my son while he did the work, then I lowered the stove top, installed the burner, and it worked like magic.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from Westport, CT
- Parts Used:
- WPY04100165
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
intermittent heat from burner
Pulled out electric heating element and replaced with new. I have had this frustrating problem for 2 years and after replacing the elements they now work like new! My only question, why did it take me so long to replace???
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dawn from Pawnee, IL
- Parts Used:
- WP660533
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Surface Burner shorted out
After finding the correct Y-frame, inches and watts in a surface burner, it was easy to just slide in the slots. Tested, and it was perfect. Now it makes all of the other burners look bad. Thanks. Your site was the only one, that I was sure I had the correct part.
Was this instruction helpful to you?
Thank you for voting!