FGP335BQ00 Roper Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Judith from Phoenix, AZ
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Bulb Replacement
I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- dan from new prague, MN
- Parts Used:
- 814269
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
igniter would glow but not light the oven
replaced the igniter with a new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from Harrisburg, PA
- Parts Used:
- 814269
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Oven gas/safety valve would not open.
My 1st thought was that the valve was bad but after watching a whirlpool video on how to trouble shoot I put an amp probe on the wire to the igniter and discovered that the amp draw was not getting high enough to open the valve. The vale calls for 3 amps but the amps on the igniter only got up to 2.4 amps even though the igniter was glowing red hot. I ordered the new igniter from PartSelect and it was here in less then 2 days. It was a perfect fit and took about 30 mins. to install and it works perfectly. I also ordered a motor and a blower wheel for a Whirlpool Electric Dryer, Model #LEC8858EQO, and it arrived in less than a day and again both items were an exact fit and the dryer now works perfectly. Great service and fast response by PartSelect. I will defiantly use PartSelect again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Holly, MI
- Parts Used:
- 316032411
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
oven was not heating up to the right temps.
removed the old thermostat and replaced it with the new one. now it works great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Lakeside, MI
- Parts Used:
- 814269
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Oven /Broiler would not ignite
Determined problem was probably the igniter and ordered one. Watched internet video on igniter replacement. When igniter came read instructions and found them incomplete and ambiguous. Turned off current to stove. As per video removed oven door, racks, bottom of oven and flame deflector (only one nut holding in place.) Could then see how existing igniter was wired and understood instructions that came with igniter. Followed instructions for installation and replaced previously removed parts. Turned electricity back on and the oven/broiler gas ignited as per usual. Job took me about an hour. Could do again in 15 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Parlin, NJ
- Parts Used:
- 814269
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Old Igniter did not generate output to open Gas Valve (OVEN)
Followed instructions that came w/ NEW PART. Very straight forward.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lauren from Delta Junction, AK
- Parts Used:
- 316032411
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
oven would not maintain heat
We took out the old thermostat and replaced it with the new one....now we don't have to buy a new oven!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary R from Byesville, OH
- Parts Used:
- 814269
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
No problem
I just followed the instructions that came with the part I had no problem at all and I'm a 72 yr old lady so any one can do it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Grant from Alexandria, VA
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Light bulb failure
Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.
Was this instruction helpful to you?
Thank you for voting!