FGP337KW0 Roper Range - Instructions

Moved oven away from wall, Turned off gas and unplugged electrical from wall. The igniter has a coupler plug that you have to unplug from behind the unit. Take out the bottom drawer. Remove the 2 nuts holding the igniter in place. Remove old igniter. Replace with the new igniter, screw in nuts and thread connector wire to back of unit. Reconnect the igniter behind the unit. Turn on gas and plug in electricity. I checked to make sure it worked before pushing it back into place. I also took time to clean up while the oven was pulled out so it took about an hour - 15 minutes to replace the part - 45 to clean up. Works and looks just like a new oven range!

Removed a cover plate on the back of the stove. Unplugged the old igniter. Pulled the bottom drawer out. Reached in under the stove and undid the 2 screws holding the igniter in place. Screwed the new igniter in and put everything back together. The only tricky bit was reaching the igniter through the bottom drawer opening.

Our oven wouldn't light as the ignitor wasn't getting hot enough. I ordered the part from your company and got it in just a few days. A quarter inch wrench and one plug, done!

I placed the new handle through the holes in the oven door glass. Then pushed the nuts on to secure it. Place the glass on the clips and tightened the screws to attach the glass to the oven door. Very simple and easy. PartSelect website was very user friendly and shipping in less than 48 hours after ordering even at Christmas time.

took off the old handle. put on the new one in 5 minutes.

The igniter would glow but no gas was released to the burner. I was told that the igniter is bad because it is not getting hot enough to open the safety valve to release the gas to the burner. I turn the gas off and unplugged the oven. Opened the oven removed the racks then removed the two screws that hold the bottom plate of the oven. Now I can see the burner and the igniter. The igniter is held on to the burner with two screws. Unscrew then and unplugged the wires. Then replaced with new igniter. Replaced everything that I removed. Plugged oven back in and turned on gas. Then started oven, it takes 45 sec. for the igniter to get hot enough to release the gas and everything was working.

I found it easy. I took my time prying off the metal rings from the back of the oven door handle with anything that has a point (a nail), then putting the metal rings back on the new handle pushing them down with my thumbs inch by inch. Key words (take your time).

most difficult part was having to pull the stove out to access the Igniter wire connector. unplugged connector, removed 2 Igniter mounting screws, installed new Igniter and connected plug. very easy project. less than 30 minutes total thanks to website for perfect diagnosis of problem

Removed bottom plate by pulling up from the back (had some resitance), Two machine screws holding cover over igniter, used 3/8" socket to remove. Pulled oven from wall to disconnect igniter @ coupler, unscrew one more machine screw, fed replacement igniter into slot and coupled, attached single screw to pipe, put cover w/ 2 machine screws on top, install bottom plate. Had to use butter knife to get bottom plate to fit into the front cabinet area of stove. Done & working fine.

Really quite simple. Remove the racks - remove the two screws in the back of the bottom plate - slide out. remove the bottom drawer. remove the two screws holding the igniter - unplug the old igniter and remove. screw in new igniter, plug up new igniter, replace bottom drawer, replace bottom pate, replace racks. I did turn off the gas and electricity to the unit before repairing - and it was easier for me to get behind the unit to unplug/plug the igniter. works great! thanks!

ordered the part and in less then 24 hours from ordering the part it was shipped and delivered and my husband and I put the part in took us no time at all very easy to do... 2 years ago i had this same problem and called a guy in the area cost me $200. I had dinner in the oven by 5 that night!!!!

Slide the teethed washers on with gloved hand, so you don't break the glass with a tool. Get them down as close as possible and then screw the peice back into place on the oven door.

Glass plate could fall to the floor and break. Need two people to change the handle - one to take it off/screw it back on and one to hold the glass in place to make sure it doesn't fall.

We ordered our part from PartSelect.com, of course, using their diagnostic tool(s). We received it very rapidly after ordering (a day or two). It involved taking two screws out of the bottom plate of the oven. There were two screws in the diverter (?), but they weren't attached to anything. I had my son, who is young, strong, and small get behind the oven to locate where the igniter plugged in. He detached it and I unscrewed the nuts holding it in place. One of them was in pretty crooked and made it a little difficult. But I pulled it out. I put the new one in place, my son plugged it in, and I replaced the two nuts, securing the new one in place. I replaced all the parts and their screws while the wife cleaned the gunk from behind where the stove sits. We did perform a quick test prior to re-assembly and it looked good. Re-attached everything, put it back in place and it's working like a dream. Just in time for Fall baked goods...

Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.