FEP310GW0 Roper Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- TROY from YPSILANTI, MI
- Parts Used:
- 814399
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Bad Receptacle
I had a receptacle melt in front of my eyes. I few questions later PartSelect.com showed me the part I needed and was checking out in less than 10minutes. Part arrived 3 days later and 20 minutes after that it was installed. I'm Amazing!!! No, PartSelect.com is AMAZING!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric from Cascade, VA
- Parts Used:
- WP3188987
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven selector switch hit by lightning-dead short
Removed rear access panel (after disconnecting plug). Removed 2 screws holding switch and attached all wires to the new switch and installed. The pictures on the website helped a lot. It's hard to order the wrong part with the information you supply. Part was delivered promptly. Overall this was a good experience. I will buy from you again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from KAMUELA, AL
- Parts Used:
- W10196406RW, W10196405RW
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
burnt out drip pans
I had been putting off this repair for months! I finally sat down to explore ordering the parts. It was so easy - I wish I did it a long time ago. When the parts arrived, they were exactly what I needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Crimora, VA
- Parts Used:
- WP8203546
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Block broke
Unplug power cord, remove wires from block. take 2 screws out. replace with new block about 15 mins. Done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Port Orange, FL
- Parts Used:
- WP8053334
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
door glide broken
removed the old ones.then installed the new ones.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gudrun from Santa Fe, NM
- Parts Used:
- W10196405RW
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replacement of drip bowll
take the old one out, but the new one in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DANIEL from sanborn, NY
- Parts Used:
- W10196406RW, W10196405RW
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
the drip bowls had rusted through
a really simple fix! the parts came really quickly and all i had to do was pull the heating elements out along with the old drip pans and line up the new pans and push back in. the drip pans weren't 100% perfect as they were a universal fit, and were missing the clips that help the heating elements i nplace, but they look fine and do the job all the same.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Irina from Green Cove Springs, FL
- Parts Used:
- W10196406RW
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Ugly looking drip bowl.
Repair? What repair? I just removed the old drip bowl and replaced it with the new one. Piece of cake.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matthew from Greenville, OH
- Parts Used:
- WPW10308477
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven not heating properly
Unplug the oven, pull it out and empty the inside of the oven. The bottom heating element just unscrews from the back of the oven with two screws. Pull it out from the back of the oven and gently pull off the electrical connections. Reattach them to the new heating element, put it back into the oven and reattach the screws. Turn the oven on and check to make sure that the new heating element is working. Put everything back in the oven and you're done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen from Maryland Heights, MO
- Parts Used:
- WP3195546
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The front drawer glide broke
Very easy. A couple of screws and it was repaired. Parts select makes it easy and affordable to do minor repairs on my appliance. This is the second time we have used this company to repair our oven and so far all has gone very well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- charlie from glenwood springs, CO
- Parts Used:
- WPW10308477
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven was not heating up to temp.
Pulled the oven away from the wall, unplugged the oven. Unscrewed the back panel(2 screws)that covers the pigtail connection. Pulled the two wires that attached to the heating element. Inside the oven i removed the two screws holding the element in place and removed old element. Put the new element in place and returned screws. The two wires clipped effortlessly on the back, returned cover and screws and plugged the oven back in. Tested the oven and returned it to its position, reset the clock and done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jon from lexington, GA
- Parts Used:
- WPW10308477
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Chared Bake element
Unplug oven, open oven door wide,pull out racks, clean reside that old element left. I used power drill with phillips head bit,pulled out old element, and disconnected wires from clips. Connected new element to wires, and Presto.Turned bake element to 300 deg.and waited only to see it red and ready to cook.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paulette J. from Connell, WA
- Parts Used:
- WP9761346
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old burner stopped working right.
Was able to unplug the old burner and plug the new one in. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Maxwell from Springdale, AR
- Parts Used:
- WPW10308477
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bottom element burnt into two pieces
Unplugged stove, opened door and removed two bolts with a phillips screwdriver. Pulled out old element and pulled off the two wire leads. Replaced with new element and reversed all steps...wallaaaaa.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- L from Richardson, TX
- Parts Used:
- WP9761346
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burned out coil
Simply slide out old coil by lifting cooktop pan; position new coil electirc elements in oven slots, slowly push in, then push coil tab into slot in pan for balance. No problems
Was this instruction helpful to you?
Thank you for voting!