RME32300 Roper Range - Instructions

After trying for many years to buy the "cheap" drip pans in the store, "They never fit right", I decided to order the correct drip bowls. Now my stove top looks brand new, and my coil elements fit the proper way.

Since it fell out, we didn't know how to put it back in--after several hours of frustration, thinking the glass was too big--we went to appliance store and looked at a stove and found out the glass went on the outside with only a groove and handle holding it in place. After that, it took about 30 minutes to complete.

I removed the two screws that held the element in place . I think pulled out the element and disconnected the two wires. I put the new element in and connected the two wires. I went to put the element back in and something sparked and burned up the wire. Lesson learned - turn the electricity off first. I had to pay a repair man to come out and replace the wire.

After searching on the internet for a very long time, we were almost ready to order the screws "blind" (no picture) from Sears for almost $10.oo per screw. Then I stumbled onto this website and found exactly what I was looking for, with a detailed description AND a picture!! Not to mention a price that was two thirds less than Sears..for TWO screws. Now the oven door is secure and we are no longer on our search for the right screws.

Removed oven door and the 3 screws holding the bottom door trim. Attached new trim piece and reinstalled oven door. Entire job took less than 5 minutes.

Removed the old burners and lifted top assembly. It made it easier to work with the wires by removing the top, easily remove the screws holding the wire harness and ground wire, then slid the top to the right and it came right off. splicing the wires in was very easy and all the parts required were sent with the kits. reassembled stove and it worked like a champ. The drawer was very easy as well the plastic glides were all broken or worn out, and one screw each to replace. like a new oven now, saved at least 300 by not purchasing a new one.

Used cooktop creme, oven cleaner and Mr. Clean sponges. After many days of working on the surface, we were able to remove 99% of the sauce.

Slide range out,unplug range,remove rear cover to unplug element wires, open door remove screws inside oven remove element

It was simple. Unscrewed to screws at the back of the oven. Slipped off the wire connectors then attached the wire connectors to the new part, put the screws back in and we were back in business.

Ordered both parts using the excellent breakdown illustrations of the door. Received the parts along with video instructions on how to repair.

1) Unplug stove.
2) Remove back cover of the stove held in place by 8 screws (4 short ones for the upper holes and 4 longer ones for the lower holes.).
3) Remove the knob from the switch that you are replacing to expose
the switch mounting screws (2 screws).
4) Remove the screws.
5) Go to the rear of the stove and extract the defective switch.
6) You will see 2 plastic plugs going into/onto the switch. Remove the
plugs. MAKE SURE YOU ARE UNPLUGGED FROM THE
Wall OUTLET!! A small flat blade may be needed to separate the
plugs from switch.
7) Attach the plugs to the new switch (there is only one way to do it.
you wont get them confused and put on wrong.
8) Put the new switch where the defective one was.
9) Come to the front of the stove and put your two screws in and
replace the knob.
10) Replace the back cover,
11) Plug in and test burner.

Unplugged stove from electrical outlet. Pulled temperature control dial off by hand. Remove screws to top back stove panel with Phillips screwdriver. Removed top stove back panel. Unscrewed broken infinity switch from stove. Unclipped wiring harness to broken switch by prying loose with flat head screw driver. Reclipped wiring harness to new switch. Screwed replacement switch back onto stove. Reattached back panel with screws.

First I disconnected the power, removed the screw that hold the element in place. Then, I pulled the element out and cut the two wires. I connected the two wires with the new element as the instruction provided by Part Select. I put the element back and screwed it in place. I plugged in the power and turned on the burner. It works. It is really easy to repair.

Made sure was off, Removed rear panel, removed 2 screws, removed wire clips from old switch, installed wires on new switch, installed switch with 2 screws, re-installed back panel, reconnected power and checked switch function. OK!

It was easy to find the part. I ordered it on Sunday and it arrived Wednesday. A stress-free experience.