FEP350YW2 Roper Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Robert from Atlanta, GA
- Parts Used:
- WP660579
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Broiler unit would not heat
The broiler unit had disintegrated at both connections. I removed the two screws in the top of the oven holder the unit, pulled out the unit, measured and ordered a replacement.
To replace the element, I pulled out the stove, removed the rear panel, located the connections for the broiler unit, remove parts of the old unit. I then attached the new unit to the top of the oven with the two screws, went around back and pushed in the two connections, replaced the back cover and replace the stove. It took about 30 minutes because I cleaned everything and sprayed bug spay (another plus for doing the repair myself).
To replace the element, I pulled out the stove, removed the rear panel, located the connections for the broiler unit, remove parts of the old unit. I then attached the new unit to the top of the oven with the two screws, went around back and pushed in the two connections, replaced the back cover and replace the stove. It took about 30 minutes because I cleaned everything and sprayed bug spay (another plus for doing the repair myself).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from killingworth, CT
- Parts Used:
- WP660533
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burners weren't heating
Unplugged old burner elements. Popped in new burners. Turned on the burners to test.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Yafa (and David) from Bothell, WA
- Parts Used:
- 8009
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Replacing the bulb in the freezer side
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rosa from Miami, FL
- Parts Used:
- 868522
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
2 Surface burner center medallions broke
Not only it was easy to install but to find them was even quicker, thanks to Part Select.com. After searching for quite some time I found the site and my problem was solved. Item was received in a timely manner and replacing was very quick.
Thank you.
Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doug from Puyallup, WA
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Lower oven element not working.
1. Turn off oven.
2. Switch off circuit braker to oven.
3. Remove two screws holding element.
4. Pull element out to expose connectors.
5. Disconnect connectors and remove element.
6. Reverse procedure for installation.
2. Switch off circuit braker to oven.
3. Remove two screws holding element.
4. Pull element out to expose connectors.
5. Disconnect connectors and remove element.
6. Reverse procedure for installation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jacqueline from Austin, TX
- Parts Used:
- WP660533
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Electric Stove Burner was working unreliably
pulled out the old burner, plugged in the new burner. Turned on the power and it heated up very quickly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GAIL from ORCHARD PARK, NY
- Parts Used:
- 330031
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Front Burner Would Not Heat
I cut the power to the circuit. Removed the burner and then unscrewed the old aluminum plate attached to the range top cover. Opened the topcover to access the wires. I cut the two wires being sure that I left enough length. I then slipped the two new wires with the brass contacts into the new black plastic holder until it locked. Reattached the new metal plate to the range cover, fed the wires through and snapped the new plastic holder into the aluminum plate. Secured wire ends with the ceramic wire nuts. Total time about 30 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nancy from Baldwinsville, NY
- Parts Used:
- 330031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burner would not heat up.
Removed 2 screws, cut the wires, pulled the part out that the element plugs into. Replaced the old part with the new one and put the screws back in to hold it, reconnected the wires and plugged in the element. Turned stove on and Valaaaa! It was fixed in 10 minutes! Thanks for the great repair parts!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lawrence from BROOKSVILLE, FL
- Parts Used:
- 330031
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Screw hard to get off
Drilled a pilot hole with a 1/16 th drill bit and tapped off screw head.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mildred from VALE, SD
- Parts Used:
- WP308180
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
unit burned out
grandson removed the two screws holding in the burned out unit and removed the two wires, installed them into the new unit and put the prongs into place. very easy and certainly very economic. delivery was quick and postage was reasonable. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LOUIS C from GRAND JCT, CO
- Parts Used:
- WP3149404
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Dual burner would go to highn heat.
Watched video & did just guy in video did. Very easy job & the burner works like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Annie S from RIDGEVILLE, SC
- Parts Used:
- WP3148953
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Burner did not always reduce heat when temp. Was lowered.
My husband unscrewed the bad switch and replaced with the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Milford, MI
- Parts Used:
- 330031
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burner inop
removed the plug that had burned up on one of the top burners, replaced it with a new plug purchased from parts select., it was quite easy ,I unpluged stove and raise the top exposing wiring for the burners cut the old plug wiring and connected the wires for the new plug with connectors and shrink tubing supplied in the repair kit easy and quick repair
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Johnson from Norwood, CO
- Parts Used:
- WP308180
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake Element Failed
I had previously partially removed the element and tested with multi-meter to determine that it was not working (open circuit). Repair procedure follows:
Turned off Power
Removed 2 retaining screws
Pulled element out part way
Removed 2 spade connectors supplying power
Replaced element w/new element
Reversed procedure
Tested Oven; worked fine.
Turned off Power
Removed 2 retaining screws
Pulled element out part way
Removed 2 spade connectors supplying power
Replaced element w/new element
Reversed procedure
Tested Oven; worked fine.
Was this instruction helpful to you?
Thank you for voting!
Intermittant Operation Of Surface Burner
I first tripped the power circuit breaker. Then I unplugged and removed the old element. Removing one screw allowed me to remove and replace the mounting clip. This did result in breaking off a small piece of plastic-like material from the electrical housing to which the clip was attached but did not hinder the replacement of the new clip. I inserted the new burner element. The surface burner is now working fine.
Was this instruction helpful to you?
Thank you for voting!