FES326RD0 Roper Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Carol from BELLINGHAM, WA
- Parts Used:
- W11594027
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Replacing oven light and socket
The old part, including lightbulb and socket, had corroded into place, and the glass light cover was stuck to the socket. I used a dead blow hammer and a dowel just under the diameter of the hole to tap on the back side of the socket to loosen it and get it out. The metal tabs on the old socket were folded back to make it fit better (?), which made it harder to remove. Lots of muscling of the part to get it out. Easy to install new part once old one was out of the way. An experienced person would have removed the old part and installed the new in no time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William H. from morehead city, NC
- Parts Used:
- W11594027
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
electrical short from oven light.
I trouble shot and traced out to electrical short in face panel and found burnt wires. I've been a licensed electrician for years and it takes alot of comon sense to trouble shoot and find problem. I found schetch-matic of appliance and searched computor and found partselect.com and tried it. It wasnt no time and the part was at my door. Thank you partselect and i would use them again in the future. billy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ryan from AUBURN, WA
- Parts Used:
- WPW10259865, WP660532, W10196406RW, W10196405RW, 814399
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Uneven heating of surface burners. Occasional electrical sound (arching) when burner was turned on. Also the burner would heat up and cool down while burner when turned on.
Replaced all heating surface burners. We noticed signs of arching on the front left (large) burner so we replaced that receptacle with a replacement receptacle kit. Very quick and easy install (5-10 mins) using the short part select video on receptacle kit information page.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOSEPH from COON RAPIDS, MN
- Parts Used:
- W11594027
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Worn/Bulb Socket
It was alittle difficult at 1st to remove the clips that held in the socket. But once out everything went smoothly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Valerie from ROCHESTER, MN
- Parts Used:
- WP3195546
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broke drawer bracket
Was super easy even I could do it. Wish I would have done it 2 years ago when my husband broke it. Just used a Phillips screwdriver. Very easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ELAINE from SILVER SPRING, MD
- Parts Used:
- WP3196231
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
THe original knob found its way into my garbage disposal and was broken. I needed to freplace it.
I decided NOT to crawl under my stove top to find the correct model no. of the unit, as recommended in the Help section of the website. Instead I just guessed. It arrived, and of course didn;t fit. So I crawled under the stove top, got the correct model no., and instantly found the correct part to order. Part Select instantly honored my request for a refund on the first part and the correct part is on its way. So I ended up paying two delivery charges instead of one. LESSON LEARNED.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from APACHE JCT, AZ
- Parts Used:
- WPW10308477
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven Elementwas burnt into
Watched the video and did as shown
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martha from EDISON, NJ
- Parts Used:
- WPW10202217, WP3196164
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door handle of stove's oven broke. Had problem finding handle until I contacted Select Parts.
The repair went well. Only took a few minutes. Oven is 21 years old and still working. I figured why throw away if still working. Thank you Select Parts for coming to my rescue. Will keep you in mind.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diane from Gillett, WI
- Parts Used:
- 814399
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Oven heating coil snapped and would no longer heat.
It was so easy to change this out. Unplugged the stove and removed a couple of screws on mounting plate and pulled out the old heating element. Plugged in the new one and replaced the screws. Problem solved!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roseann from MEADVILLE, PA
- Parts Used:
- WPW10259865, WP660532
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
2 Service Elements Didn't Work (Didn't heat up)
Unplugged old elements and plugged in new ones
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from DANBURY, CT
- Parts Used:
- W10196405RW
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old drip pans made to heating element un ever
Replaced drip pans and now everything is level.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from Greensboro, NC
- Parts Used:
- W10856603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Oven Demon Possession
Our repair was extrodinarily easy. As my husband was taking out the old element and the oven was off, the element heated up and actually burned him. He readjusted it and it refused to heat again. We figured at that point that there must be a short, so we never even opened the box with the new element. A short time later we decided to use the top of the stove for soup and a small fire started in the oven. We turned off the braker at that point and ordered a new oven.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PHILIP from NORTH PORT, FL
- Parts Used:
- W10856603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
element not working properly
Remove 2 screws inside oven holding element . Remove screws holding back panel. Plug wires (2) into new element.Install back panel . Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from THE VILLAGES, FL
- Parts Used:
- WP3149400
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Burner wouldn't regulate temperature
Turned off power to range. Took back panel off to reveal all controls. Pulled off knob of bad control. Removed 2 screws from the front of the control. Pulled off wiring from back of old control. Took new control reversed procedure. Reinstalled back panel turned power on and tested new control. Total time about 20 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nathan from WHITE RIV JCT, VT
- Parts Used:
- WP3148952
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Element temperature inconsistent
Turn off power to the stove (unplug or turn off breaker)
Remove back panel screws (Phillips) and back panel
Unplug switch
Remove knob and attaching screws (Phillips)
Remove and replace switch
Reinstall screws for switch and plugs in the back
Snap off the end of the stem if it's too long and reinstall knob
Reinstall back panel and turn power back on
*important: the large element has an updated switch and you may need to snap off the end of the stem with pliers! It's too long and there are no instructions for this included!*
Remove back panel screws (Phillips) and back panel
Unplug switch
Remove knob and attaching screws (Phillips)
Remove and replace switch
Reinstall screws for switch and plugs in the back
Snap off the end of the stem if it's too long and reinstall knob
Reinstall back panel and turn power back on
*important: the large element has an updated switch and you may need to snap off the end of the stem with pliers! It's too long and there are no instructions for this included!*
Was this instruction helpful to you?
Thank you for voting!